I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
I use SDKv2 . 09 . 00 without using the eSB function timelot can trigger MPSL_TIMESLOT_SIGNAL_TIMER0 normally，then NRF54L15 Running esb and BT at the same time with MSPL cannot...
After a lot of efforts I managed to autoprovision and autoconfigure my nrf52840 board and a series of nrf52840dongles (provisioning and configuring inside the software and...
Hi,
I have a Thingy:91X which connects fine to hello.nrcloud.com. Now I want to connect it to my own nRF Cloud account.
Note that I have successfully provisioned multiple...
I am working on a project using the nrf9160DK for initial firmware development. Trying out the SAADC i encountered that the measured values were always about 20% lower then...
Dear Nordic Team,
I hope this message finds you well. We are currently using the nRF9160 in our product and have a few questions:
Can you confirm the ongoing availability...
Hi, With this setup in , I successfully built a CIS mode using my nRF5340 DKs , enabling stereo sound while the microphone is active .
However, I am currently experiencing...
Hello,
I would like to ask how to update the appName field in the shadow register on the nRFCloud, using CoAP protocol.
I was able to change the appVersion by passing...
Hello,
I am a developer/maintainer for the RF24 Arduino library at https://github.com/nRF24/RF24
I've found in some cases, the R_RX_PL_WID register returns 0 while the...
We've got a sensor board with an nrf9160 on it, that sleeps lots of the time and periodically wakes up to take sensor readings or send them up to the cloud.
Some of the...
Hi,
We are developing a mouse for Dell.
We have based our project on the nRF desktop project.
Our mouse is working, but we are having pairing issues in that once it...
So whatever I try, the only way to get my idle current consumption to an acceptable low value is to set CONFIG_SERIAL=n in my configuration. But then I don't get printk functionality...
Hello,
I use SDK v2.9.0 with nRF52840 and my application is based on peripheral_uart example.
Have I understood correctly that nRF52840dongle has preloaded (by Nordic...
Hello,
I’m currently working on a Bluetooth Mesh project using Nordic Semiconductor devices, and I would like to get guidance on static provisioning and group-based communication...
Hello,
I'm working on a project that uses the Serial LTE Modem (SLM) application on a custom board. The main processor sends data to the nRF9160 over UART. The project is...
Hi,
I am currently working on evaluation of the nRF52810 for a simple project which requires a very low power consumption. I searched and found an example which I modified...
