Hi there,
I have recently upgraded my software to latest ncs 3.2.0. I have noticed that my initialisation does complete but it ends up with fatal error that seems to be...
Dear Nordic,
I am debugging a custom hardware with a nRF7002 on-board, using wifi shell app. At this moment the shell does not work as expected, needs to locate where the...
I am attempting to install nRF Connect SDK along with VS Code on an offline machine for development. The main two issues I have are:
The NRF Connect for VS Code plugin...
Hi
I am using the nRF54L15 DK and build a thread continueing monitor the data rate in 1 Hz, if it is lower to 800kbps I want to change to 1M; while above 800kbps I want...
Hi all,
I’m Bruce — first-time poster but have been working with the nRF9160 on and off for a while now, mainly in outdoor, power-constrained telemetry and monitoring applications...
I have a simple GATT server application with two characteristics, RX and TX. In my prj.conf, I am trying to disable pairing as follows :
I can connect to the server from...
Hello,
I am trying to use LTE connectivity on a custom board with a nRF9160 SICA B1, but i am facing issues with the modem.
With both my own app firmware and the sample...
Through a few days of studying, I now decided that: (please correct any statements I said wrong below)
The BLE is more friendly to object oriented programming
...
I've been a little out of the loop. Can someone explain how this "drag and drop" DFU is working? And in what method iTunes is being used!?
Best I can figure iTunes is being...
Hello everyone. I am having problems using the interrups when a bootloader is programmed on the chip. My test program works fine when there is no bootloader. With the bootloader...
Hi,
I try to turn off the advertising after the first connection and then turn it on after pressing the button, this is what I wrote:
void radio_notification_evt_handler...
Hi,
I've been digging through a lot of AN's about how to design a PCB antenna, in all of them an important parameter is the output impedance of the transmitter.
So,...
Hello,
I'm pretty much new to NRF development and I'm having lots of questions trying to get a custom board to work with the provided BLE bootloader example in SDK 11....
Hi all,
Hi I am implementing MQTT client on the Nrf52 MCU, as to the MQTT broker, I am going to use the amazon AWS IoT , where the broker adopts the TLS 1.2.
I read...
I am using nRF51 and latest s310 softdevice (3.0.0) and latest SDK (v10), which is the latest compatible with the softdevice.
My device is programmed with the softdevice...
Hi,
I'm designing a 2 layer flex PCB with the nRF51822-CFAC WLCSP package and recommended ST BAL-NRF02D3 balun and on-board PCB passive antenna (not ceramic chip antenna...
Hi Friends,
I am using nRF51822(S110 and SDK10.0.0) in my project and I need the chip to be in connectable and advertising mode under peripheral config . I configured the...
Hi,
I have migrated application with freertos (S132 /NRF52 devkit ) from SDK 11.00 to SDK12.00 .
Flashed SD 3.00 and then application ,but Application is not able to boot...
Hi,
Is this the right way of reading the timer value using the capture task. In this code i am trying to read the updated value of counter for every event generated in...
Hello;
I'm developing an application that advertises as a connectable peripheral. As such, it has an ID (think of it like a beacon minor).
I have 2000 of these devices...
Does bootloader example dfu_dual_bank_ble_s132_pca10040 from SDK v11 work with softdevice v3.0?
when I try to run the dfu_dual_bank_ble example with softdevice 3.0, I got...
