We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
Hi,
I am creating an application based on ble_app_hrs_c (central role). I have a few questions on this.
o I do not understand whitelist_load(). It first gets a list...
Good morning Nordic team,
I was measuring the nRF52832 chip in DC/DC mode. Everything went just as expected.
Now I was looking at the current consumption when the radio...
Hi guys. I have a EVK_NINA_B1 board which is based on nrf52832 and SDK12. I am trying to run the ble_peripheral/ble_app_uart/ from examples. I can send message through "nrf...
Hello,
I use SDK 11 with nRF52, softdevice s132.
I am able to successfully use the bootloader in serial mode (with UART) to upgrade the application, but an error occurred...
hi nordic,
After i received this kit from Mouser Electronic, when i got it check the board which some question,
we examined its outward appearance and found that this...
Hi,
I have my nrf52 DK. I would like to advertise as Beacon and be BLE (which I can connect to via iOS app) device at the same time. Do you know any examples of this kind...
Why does the macro CHECK_RAM_START_ADDR only check for C_LINK_CNT and P_LINK_CNT and not the SEC_COUNT? It is always set to 0 in the macro.
I have increased the central_sec_count...
Hi ，
I use timer to handle pwm signal,
1.when calling button by phone is pressed,
Timer starts,(function:on_key_trig_speaker_event())
2.pwm signal run (speaker_meas_timeout_handler...
Hello,
My name is krishna,
I have couple of NRF24L01+ modules,
I am trying to implement MultiCeiver in the NRF module.
The problem is i am able to receive or transmit...
Hi,
I am trying to compile the ANT Broadcast Tx Example from the latest nRF5 SDK v12.1.0 (../examples/ant/ant_broadcast/tx), but I get the following 3 error messages with...
Hi,all
I use nrf51822 connect with ios device,it will automatically disconnect when links more than 90 seconds.
device connection parameter as follow:
#define MIN_CONN_INTERVAL...
Hi I'm using the Jlink to program nRF52832_XXAA, by using nRF command V9.0.0 nrfjprog
I success in erase , but I can't program correctly,I tried Jlink version 5.12g and 6...
initially we developed code for arduino mega board but now we want to use the nRF51822 soc,so how i can utilize my arduino code for nRF51822 ....i have gone through the some...
