I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
Sir,
We finally added WIFI to NINA B302, using a NINA W102 coprocessor!
https://github.com/khoih-prog/WiFiNINA_Generic
Please, enjoy!!!
Here a portuguese BLOG...
Hello!
Does anyone know of a library for the I2C LCD 16x2 display? I found the library by lovee, https://devzone.nordicsemi.com/f/nordic-q-a/23401/nrf52832-connect-with...
Hello,
I'm having problems running the DFU over serial bootloader example. The nrfutil command to update the application fails with message "timed out waiting for acknowledgement...
Hi together,
I'm trying to scan for BLE Beacons and I got the problem that if I set setReportDelay() to a value unlike zero, the onBatchScanResults() method is called and...
Hi,
I am trying to measure the current consumption on my application, and measured some quite high values even after calling sd_app_evt_wait().
After reading through some...
We have a product that uses nrf51422_CE_AA, Revision 3, 256KB ROM, 16KB RAM, PCA10028, SDK 8.0.0, S110. We have sold over 8000 devices of our first product. Currently we are...
Hello,
My problem is to much current c.a. 40uA in POWER OFF mode. Below attach code:
void power_down()
{
nrf_gpio_pin_clear(22); // Wylacz mostek tensometryczny
nrf_delay_ms...
With nRF52832 DK I have managed to compile this blinky example:
#include <stdlib.h>
#include <stdint.h>
#include <stdbool.h>
#include "nrf_delay.h"
#include "nrf_gpio...
I am getting no radio (as in not being able to pick up advertisements packets) from my custom nrf52832 board. The antenna design is a hack so I am not looking fo stellar performance...
We are looking in to developing a generic class to connect and handle our BLE devices for use on mobile devices such as Android and iOS.
Now since we want to have as less...
Hello Experts,
I am running the following examples to test the DFU bootloader in gcc and eclipse environment.
bootloader_secure/pca10040(Bootloader) and experimental_ble_app_buttonless_dfu...
I found a problem of the nRF51822 in boot state.
Power on reset is not executed occasionally when used dying battery.
The problem occurs in the following steps:
...
Hi All,
I'm having a BTLE_CONNECTION_TIMEOUT when I connect the device in Master Control Panel 3.10.0.14 while the chip is not in debug mode.
The device connects without...
Hi
I am trying to upgrade the firmware in a BL652 using a Segger Jlink Edu.
The BL652 is powered with 3.3v using a regulator off the JLink 5v output.
I had poor/unreliable...
I am using a processor that can provide an 32KHz clock (from its crystal).
Can you recommend the voltage divider (caps or resistors and suggested values)?
I will power...
I added a task to ble_app_hrs_freertos.
The soft device was burned.
The address is in the default state. (RAM:0x20002128 ROM:0x1f000)
I reset the total heap size...
