Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
I was wondering what would be a good block size, and saw this in the documentation:
For example, if a module has a table with 10 entries, and each entry is 64 bytes...
Hi Nordic,
I am now trying to use ANT acknowledged data type in reverse direction (from slave to master), and I have some questions:
When sometimes, ack signal...
Hey, I want to save stuff to flash under the same id and key which should be no problem as shown in the documentation. But when I save it and retrieve the data only the last...
hi,
i am newer here.
i am confused in nrf_gpio_pin_sense_t i.e. NOSENSE, HIGH_SENSE, LOW_SENSE.
where is use of this feature ?
why it is required instead gpio_input...
In my application many nodes (acting as centrals) will start simultaneously, as they have common power supply. I am using s132 SoftDevice (4.0). Is the frequency hoping sequence...
Hi experts,
Can we add capacitor to the swdio pin to improve ESD capacity?
We have make some sample that add 1uF capacitor to the swdio, indeed have improved the ESD capacity...
hello there i want to use c++ library in nrf51dk project. i am using sdk12.
i change main.c to main.cpp
but i am getting error. uart_original.rar
i have uploaded code...
We are planning to use two modules at the same time one for esb and one for standard btle, because the esb is time critical and timeslot api seems to be to low priority. Do...
Hi,
I am using NRF52 DK board. I use nrfjprog under windows to flash controller. But i want to flash under ubuntu. I searched but i found one .rar file.i extracted but there...
This is probably a sign that I should upgrade to nRF52 (with a built-in FPU) but, in the meantime, does anybody have an example of the libfixmath library integrated with an...
Hi everyone,
i have J TAG V8 and when i am using this with keil software and try to debugging then its showing-
"The connected emulator can not be used with this software...
I found in documentation that the time to write to flash is between 67.5 and 338 µs.
What conditions influence this time?
-How to avoid long writing times?
I have four wearable devices.
Each of them have 50HZ sample rate, and data length is 20Byte.
I don't want to lost any data, so I want to use indication instead of notification...
