nRF54L15 would be used as thread RCP, host processor would use uart to communicate with the rcp. They would behave like a OTBR.
I also need to do device firmware update...
Hi
I have two DKs, previously they work well, however, after I add the nRF21540 FEM on each DK, I always receive this in my central device:
Whether the amplifier cause...
I am attempting to install nRF Connect SDK along with VS Code on an offline machine for development. The main two issues I have are:
The NRF Connect for VS Code plugin...
Hi,
We're working on a project using the nRF5340, where we interface an external NAND flash (4096 blocks) to store high-volume sensor data. We are planning to maintain an...
Hi,
We are currently evaluating the NRF9151 for asset tracking using the AT firmware on the NRF9151 evk and an external MCU for the application firmware, emulating the final...
Hello team, I am currently working on the distance measurement functionality using the development kit (nRF5340 and SDK: v2.9.0). At present, the distance measurement runs...
[ Just figured out it doesn't work the way I thought ]
Hi,
Right now I'm looking down at the nrf52840 datasheet, because I would like to do a project with such MCU, but...
We are looking in to developing a generic class to connect and handle our BLE devices for use on mobile devices such as Android and iOS.
Now since we want to have as less...
Hello Experts,
I am running the following examples to test the DFU bootloader in gcc and eclipse environment.
bootloader_secure/pca10040(Bootloader) and experimental_ble_app_buttonless_dfu...
I found a problem of the nRF51822 in boot state.
Power on reset is not executed occasionally when used dying battery.
The problem occurs in the following steps:
...
Hi All,
I'm having a BTLE_CONNECTION_TIMEOUT when I connect the device in Master Control Panel 3.10.0.14 while the chip is not in debug mode.
The device connects without...
Hi
I am trying to upgrade the firmware in a BL652 using a Segger Jlink Edu.
The BL652 is powered with 3.3v using a regulator off the JLink 5v output.
I had poor/unreliable...
I am using a processor that can provide an 32KHz clock (from its crystal).
Can you recommend the voltage divider (caps or resistors and suggested values)?
I will power...
I added a task to ble_app_hrs_freertos.
The soft device was burned.
The address is in the default state. (RAM:0x20002128 ROM:0x1f000)
I reset the total heap size...
Hello i am quite new to using BLE for data collection. I am using a Readbear BLE Nano with a Nordic nRF51822 on it.
I want to read a Sparkfun MMA8452Q accelerometer's X...
Hello, if I disable interrupt on nrf51xxx device, function sd_ble_tx_buffer_count_get will simply run right into hard fault handler, without returning anything.
I do not...
Hi,
on NRF51 BLE peripheral I want to implement authentication, so only selected BLE masters have access to my BLE peripheral.
There is a password known to BLE peripheral...
Regarding the RTC prescaler of nRF51822,
I found out that it is the following.
Timer and RTC prescaler behavior by TASKS_CLEAR is different,
When TASKS_CLEAR is executed...
My company is making capacitive touch plates and to make them smart, app is used.We are using NRF24L01+ for rf communication between device and app. Our sockets and hub with...
I did some modification from radio test example.
But I don't know why the function "rand8" never ending.
In the function, rand8,
NRF_RNG->EVENTS_VALRDY = 0;
while (NRF_RNG...
Hi,
I have been trying to get up and running since the first DK was released for nRF52x and I am yet to have installed a working development environment. I have tried to...
