Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hello, I work with some ADC 24-bit (HX711) and for getting data from that I need after low level on first gpio pin to fed 26 pulses to that with time period about 1us on second...
Hi,
I am using ble_app_uart_c_S120
How can i support more then 1 bonded connection?
i try:
#define DEVICE_MANAGER_MAX_CONNECTIONS 7
#define DEVICE_MANAGER_MAX_BONDS...
What's the correct settings for nRF51822 CEAAE0 (0x0079) with dfu example in SDK v11 ?
I believe the chip I am using is a 16KB ram 256KB rom version, but not sure 51422 or...
reco_scan_req.PNG
Now i am doing a test of RECO beacon which use a nordic chipset, nrf51822.
But something strange came up to me during the test with Ellisys bluetooth...
Hello,
I know that this question has been asked in the past but I could not find any recent post about this topic, and there have been many updates to the SDK since the...
I am using NRF52DK and SDK 12.1. I am using BLE. I currently am not using Peer Manager but probably will be implementing that in the future (of sooner if that makes my question...
Actually, nRF 52832 DK has Type-2 NFC Tag. For type-2 NFC TAG, its data access method can be read/write or read only. Therefore, does Nordic have any example codes of two...
Hello,
there is written that Peer Manager is using flash for storing bonding data or service configuration. Can you extend a documentation - and add description when and...
Hello,
I have platform base on nrf51822, collecting data through I2C and sending to android application.
the device is working according following protocol:
Motion data...
Hello,
I'm developing firmware for a BLE central that performs a DFU on another NRF target. Right now I'm at the point where I need to start sending the firmware image...
Hi All,
I am using nrf51822 with S130 softdevice & SDK12
i am using Eclips IDE for development.
i am defining BLE_STACK_SUPPORT_REQD in makefile by
CFLAGS += ...
Hello,
While looking for examples, I found a post from 2004 where a user is asking a question about an example code for HID on nRF8001. Is this code still available? Where...
Hi Nordic,
Our device as master need to pair with android APP. We want to add function that pair with secure key. when APP pairing with our device. Our device will display...
Hi,
I use software s132 PCA10040, SDK 11 and NRF52832. I need to control the swap space region.
In 512kb, total 120kb is allocated to softdevice and bootloader.
My application...
