Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
I have designed this schematic according to reference designs provided by Nordic Semi, however I might have failed as I am unable to flash the main module. I should...
I'm adding CONFIG_NET_CORE_MONITOR in both application and network config per https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/libraries/others/network_core_monitor...
Hello,
In ncs, I am working with \nrf\samples\ipc\ipc_service. I want MCUboot to build \nrf\samples\ipc\ipc_service\remote to run on nrf5340 CPUNET. When I CONFIG_BOARD_ENABLE_CPUNET...
I use NRF54L15 DK to develop channel sounding feature on zephyr SDK or nRF connect SDK.
How to configure CSTONES related registers to transmit and receive CS Tone packets...
Hello,
I’m working with a custom board using the nRF54L15 and the latest Nordic SDK, and I’m facing an issue while trying to communicate with an nPM1300 over I2C.
Here...
Hi all,
I'm working on a project with an nRF52840 using the nRF Connect SDK (version X.Y.Z) and Zephyr RTOS. My goal is to achieve maximum possible range for non-connectable...
Hi,
I'm trying to run the Lesson 4 Exercise 2 solution from the Nordic DevAcademy BLE Fudamentals course (origin/v2.9.0-v2.7.0) run on a nRF54L15 PDK board.
I'm currently...
Hello, I am trying to use the subghz template in ncs 2.5.2 but I am running into an issue when enabling NanoPB. When enabling NanoPB with CONFIG_NANOPB=y the application faults...
nrf modem: 1.3.4
sdk: 2.3.0
Custom board.
We have an asset tracker that caches events when out of connectivity zone. We can accumulate 10-100 messages depending upon...
When calling the bt_conn_le_create_synced function to create a connection to a peripheral, which is synced to the PAwR train, I get a CONNECTION FAILED TO BE ESTABLISHED ...
Hello!
I have designed a custom board with the nRF5340 , powered at 1.8V. I am able to program the chip successfully, but after the firmware is downloaded (Zephyr RTOS,...
Hi All.
I am trying to measure the consumption of the SoCs inside the nRF52840DK and the nRF52833DK using a PPK(II), both running the same code to make comparisons.
First...
In my application we have an nRF514L configured as an SPI target. Page 830 of the nRF54L datasheet (version 0.8, dated December 2024) documents that the SPIS peripheral requires...
I'm trying to convert some code from ESP32 to nRF, and I'm having problems with the microphone input. Mind you, I'm a beginner with nRF, so I'm sure I'm missing something...
