Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm using peripheral_past sample on nrf5340 audio DK board, and select nrf5340dk_nrf5340_cpuapp_ns for Build Target.
I added the following config to enable RTT...
Hello, I am working on a project where we use MCUBoot.
Currently everything works fine, but now we wanted to introduce persistent storage of some key value pairs.
For...
Hi Nordic Team,
What is the difference between 10 bit, 12 bit and 14 bit operation mode and 8/10/12/14 bit resolution in SAADC of nRF54L?
Best regards,
Bhavya
Hello,
I'm using nRF54L15DK and nRF Connect SDK 2.9.0. I'm developing a project for PID control of the temperature of a peripheral, let's say a heater. The feedback is...
Hi,
Not able to compile hci_uart application on latest nrf-sdk Following is error :
test/zephyr=ZEPHYR_BASE -fmacro-prefix-map=/home/abhinav/nrf_latest=WEST_TOPDIR -ffunction...
When programming a nRF9151 firmware on to Thingy91 X, I made a mistake and failed to change SW2 from nRF53 to nRF91 (the label is very small). The USB serial port no longer...
Hi,
I have finished some code with nRF54L15 and nRF52833, now I want to add nRF7002 to my design and I am wondering whether this is available?
Thank you!
Hello, World
Please note that the following questions may be difficult to read as the text was created using a translation tool.
I have downloaded version 17.0.2 of the...
Hello Nordic Team,
I am working with the nRF5340 Audio DK as a central device , trying to establish a secure connection using Security Level 4 (128-bit encryption with LE...
Dears,
I made custom board using nRF52832 and tried to write FW in flash. But I failed it.
*. HW JTAG : J-Link V9+
*. SW tool : nRF Command Line(nrfjprog)
Step #1...
I'm trying to run the 32 MHz SPI00 on the nRF54L15DK to communicate with the MX25R64 flash. However, the clock signal I'm measuring is limited to 8 MHz. Do you have any ideas...
Hi.
I am developing with NCS 2.7.0 using 5340 and have configured it to use 5 generic switches. These work fine. However, the order of the switches displayed in "Home" on...
Regarding the schematic for nRF54L15 DK I currently see on the site that the link to the schematic is disconnected, can you please provide the URL where the schematic is available...
