Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hello
In case a connection is disconnected locally by calling sd_ble_gap_disconnect(), no BLE_GAP_EVT_DISCONNECTED is fired even though the sd_ble_gap_disconnect() function...
Hello, I'm trying to optimize power on HID Keyboard app.
This post was helpfull but yet some questions remains.
If I use several services, and want central to be abble...
After S110 7.1 ble_stack_init(), any read/write to temperature register cause a HardFault.
Some sentences like:
nrf_temp_init();
NRF_TEMP->TASKS_START = 1;
...
Hi --
I am using the ble_peripheral/ble_app_hrs example project. And if I try to update the vs_uuid_count param to 2. It proceeds to fail the softdevice_enable with error...
Hello,
I'm currently looking into the secure bootloader from the 12.2.0 SDK, and wondering if there is some example code regarding implementing a uart transport?
I use the software S110 v8.00,and the NRF51822QFAA chip.
now ,I need add DFU Service support to an application.
I find the ble_peripheral\ble_app_hrs\pca10028\s110_with_dfu...
What's the best way to debug an application that is not starting after an OTA DFU update. The app said the update was successful but nothing booted and it didn't even seem...
I find the dfu sdk for ios in github ,but I only find the swift pods, did`t find the code for objective-c.
Did someone have ? Please share to me, Thank you !
Hi,
when developing I often use Google search to find documentation. I prefer using external search engines, since this includes results from StackOverflow and similar sites...
Hello I'm trying to setup i2c/twi communication between nrf52832 with oled driver SH1107 but i need to do it in hardware instead of software but on the register level.
...
Hello,
My setup is as such.
I use SPIM1 and SPIM2 all the time. SPIM1 goes to a set of MEMs devices, and SPIM2 is dedicated to a Memory module.
My device runs in of...
20170119_104909.jpg
I'm working with a ble open source.
Here i attached the captured abnormal case of the connection update
Request PDU from the slave. Please refer to...
Hi
I ordered Nrf52832 DK board instead of ordering nrf52840 Preview DK. I need to test bluetooth 5 stack,range ,bandwidth and through output.
Is the nrf52832 will support...