When flashing with SDK v3.0.1 the following error occurs:
-- west flash: using runner nrfutil -- runners.nrfutil: mass erase requested -- runners.nrfutil: reset after flashing...
My product has nrf52840 with usb mass storage configured using 8MB QSPI flash (same chip as the nrf52840dk - MX25R64)
I would like to allow users to upgrade firmware by...
Hello, I've recently upgraded my pre-production application on nrf52832 from NCS v2.6.2 to Ncs v3.0.1 also upgraded to HWv2(on interim ncs 2.9.0 as adding custom board for...
Hi,
I have set up a destination in the the NRF Cloud Message Routing Service
The destination has been verified and I can successfully send the test message from NRF Cloud...
I'm currently working on configuring the nPM1300 used in our custom board. In the product spec v1.2, it supports 2 USB compliant current limits, IBUS at 100mA and IBUS at...
Hi,
I am currently trying to enable the GPIO output interrupt functionality on my nPM1300ek with an STM32. However, I am unable to get it work correctly(I was only able...
Hi,
What is the lowest possible current consumption for nrf52840 dongle dev board with zigbee ?
I'm using this for development and i'm getting 20-30uA in idle. Is it possible...
Hello everyone,
I am currently using a nRF52832. I've been trying to use the low power mode with little success. I have been seeing a current draw of about 3.5mA. I would...
I am using an NRF52 dev board to develops a device that connects to an Android and IOS device.
I am unclear on where pairing comes into play with relation to connecting...
Hi in my project I am using nRF5_SDK_11.0.0-2.alpha SDK, s132_nrf52_2.0.0-7.alpha_softdevice. and nrf52 DK board(PC10040).
My issue is, when I run the ble_app_uart example...
Since PStorage has been removed and replaced by FStorage on SDK12, why is PStorage still listed as Experimental in the Documentation? It would appear that if you are removing...
Hello,
I am aware that according to IEEE standards RSSI value that chips return is not officially related to mW/dBm. However the values returned by your chips seem to be...
Hello,
I am trying to use timer with Bluetooth application . I want to provide precise time stamping using timer for each bluetooth event. But program execution stucks...
Hi,
I'm using nRF5 SDK V11、s130_nrf51_2.0.0_softdevice. My application has added the DFU service . I download application,softdevice and bootloader to nRF51822 AC, the...
i m using pca10028 with gcc tool chain setup in windows...now i m using sdk 8 and work inside ble_uart code...i was add rtc1 inside that code sucsessfully but now.. when device...
Hello,
I am currently testing the nRF51 series as a possible upgrade to our products that use the 24L01P. For testing I have the nRF51 dev board setup as the PRX and a...
I'm using SDK 11 on my nrf51 chip. I'm trying to output a 120hz pwm but it doesn't seem to be producing at 120hz. I have a 120hz signal i'm trying to match and it blows pass...
Dear Wang,
I am unable find any documentation and board Initialisation code on how to change PIO from analog to digital output. but can't seem to locate the setting.
...
Hi,
I am working with MLX90615 sensor and is working with nrf_drv_twi functions and I could collect data as well. Now I need to put the sensor to sleep mode. Entering to...
Hi,
I'm trying to connect DWM1000 with SPI using spi_master.h.
When I have written to registry e.g. 0x11, 0x12 and read it I've got bytes: 0xFF, 0x11.
If I read three bytes...
Hi
I'm wondering if anyone have had any success or problems with generating and using secure DFU keys under Linux?
I'm using the latest nrfutil from: github.com/......
