Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hi!
My idea of sending a packet would be:
-regulary send a packet with fixed length (stated in static length field) to a base: i.e send the temperature =>4byte
-if...
Hi,
I use the nRF51822 on the PCA10001 and nRF6310/PCA10005 boards. I modified the radio_tx_example and wanted to read the actual state of the radio. Therefore I used a...
Hi
Could I modify HID report descriptor length over 255 bytes? In Desktop1.2.2.293, the returned descriptor size is only decided by wLength LSB byte and ignores MSB byte...
Hi,
I am trying to figure out how I can advertise with a custom UUID...
I know I have to start by adding a base address and then build on top of it. However, when I try...
I have a system that uses 5-byte addresses. The first 4 bytes are always the same, but the last byte has 4 different values. For test purpose I want to listen, from another...
Title says it all. My nordicsemi.com id/pw is not working here. (But it isn't working there either. I'm getting the following error, which I presume is some breakage in the...
I have a customer that wants to be able to have a single nRF51822 sends sensor information to two iphones at the same time. Is this possible? Can you pair a peripheral to...
Hello,
I have a question....
I have real ECG device and I almost got PCA10001 development board. Studying about PCA10001 I noticed that this board has ADC. I downloaded...
Hi,
It is not transparent to me, how can I determine this value? Is it a best practices value?
I want to implement Tx Power profile but I don't know where to get this...
Dear Nordic support team,
What is the maximum number of timers that I can create (and use) using the app_timer lib?
err_code = app_timer_create(&m_timer_m_1_0,
APP_TIMER_MODE_REPEATED...
I've recently started sharing development activities with another developer. I created a GIT from the folder: C:\Keil\ARM\Device\Nordic\nrf51822\Board\pca10001\ble\myProjectFolder...
I'm leveraging off the heart rate sensor example to create my own VS service. I've successfully registered a 128-bit UUID with the Soft Device which is enumerated along with...
