Hello,
I'm using two nRF9161 to communicate with each other and I want to test and measure the differences between the 3 modes available in SDK3.0.0. First, I configured...
I have tested the nRF Cloud Multi Service Sample using Quick Start and it works perfectly.
I am trying to build the sample so that I can make small modifications for an...
Hi,
I am currently using 54L15-DK to create a radio test example, but there is a problem when I build the project: - sdk version: v2.9.0 - toolchain version: v2.9.1
...
Hello everyone,
We are developing products with nrf52840 and our default supply voltage is 1.8V.
Is it possible to program a custom 1.8V board with nRF52840DK?
We are...
Hi
I am using nRF52840 with SDK 15.3.
I have a project where I uses FatFS to write to a SD-card with SPI interface (SPIM3). This works very well.
I am now trying to...
Hi everyone,
I'm currently following the "WiFi Fundamentals" course provided by Nordic, and I'm encountering issues with this specific exercise (l5_e2):
To ensure I wasn...
Hey so I just wanted to use the BMI270 on the Thingy:53 and Polling the acceleration values seems to be working just fine. I wanted to use the DATA_READY Trigger. I am working...
Hallo,
i'm trying to test my BLE aplication using the PTS. The profile test are mostly OK. But if i run the GAP Test (especially TC_BROB_BCST_BV_01_C) the PTS does not...
It seems that static and global data is NOT set to zero during start-up. This is supposed to happen according to the C-standard. How to do this in a proper manner, i.e. to...
Hi All,
we currently move our custom design to CE testing and already did some successful EMC pretesting.
However, our testing house asked us to prepare a firmware for...
Hi All,
BLE Nordic Stack: 0.9.7
Tiny Circuits: Ardunio + Nordic nRF8001 Board
First time post, and hoping someone has run into the same issue that I am. I am in the...
Hello!
I am working with the example mpu interface projects located at the following repo:
github.com/.../nrf5-mpu-examples
After converting the Keil projects to...
Hi,
After I've successfully connected my smartphone via nRF Toolbox's UART-BLE Service to my nRF52 peripheral, I tried to mimic the scenario when the devices get disconnected...
Hello
I want to understand how far the firmware that is burnt on to a Hardware is protected. Is it possible to actually read the firmware from a device (if the device has...
Services Setup
I am trying to feed the "Services Data" manually to the nRF8001.
As per the data sheet page 82 (see image below): Upon transmission of 1 packet of data...
I am trying to run the ble_app_beacon example on an nrf51802 device.
The call to sd_softdevice_enable() never returns (jumps to 0xFFFFFFF9)
The fault handler is not called...
My guess is that:
Characteristics are (or at least, can be considered) subsets of services, which in turn, are (or at least, can be considered) subsets of profiles.
...
Hi, I am modify the S120 multi-link UART example code (code is available here ), and just noticed a problem that the central is only able to send the UART data to the last...
I have tried to make IAR working on monitor mode.(Follow this devzone.nordicsemi.com/.../ . )...up to today the NRF52 still will reset once I hit breakpoint on power_manage...
I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
Hi, we are updating our current application to the new nRF5 SDK and S132 v2 softdevice but we got stuck with a issue on the initialization of a custom service.
We narrowed...
