hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Error: L6218E: Undefined symbol ble_bas_battery_level_update (referred from main.o)
Error: L6218E: Undefined symbol nrf_drv_saadc_buffer_convert (referred from main.o)
Hi devs,
I am working in an nRF52 DK.
The attached example is not working when I change the SCL and SDA pins of TWI1 module. This is also not working if I disable TWI1...
Hi,
Is there any software I2c library or example projects for nRF52 devices (PCA10400) with pin configuration, read and write functions? I am using an SMBus based sensor...
Hello,
I am testing the ble_peripheral example of ble_app_uart (SDK 12, soft device 130), this has been asked at a lot of places that the MTU is limited to 20.
But then...
Hi,
I am using nRF51822 and implemented timer-2 with 2 sec capture/compare interrupt rate. But if I want to read timer's current count before it generates interrupt or...
at nRF51 SDK v9.0.0, S130, PCA10040, at peripheral side
If we receive a characteristics less than 20 bytes, we can get the correct handle value(like 0x3B). And then everything...
I bought nRF51-DK yesterday.
I installed nRFgo Studio(1.20), Keil uVision(5.15), Softdevice s110 (8.0.0), J-Link(5.00),
nRF51 MDK(7.2.1)
I turned on the nRFgo studio...
Hi,
I'm using Eclipse Mars 5.2 on Windows 10 along with the GNU Toolchain as described in the "Development with GCC and Eclipse Tutorial" by Vidar Berg (Thanks very much...
Hi, I can't get SPI slave mode working on nRF51822. I'm using the Core51822 module with a BLE400 board from Waveshare and up to date mbed. SPISlave::receive() always returns...
I implement it with sdk 11.0 and a third party core-board.Firstly,I program s132_nrf52_2.0.1 SoftDevice by nRFgo Studio,then I open ble_app_hrs s132_with_dfu(arm4) project...
Hi,
Currently I'm using internal RC osciallator for LFCLK on the system that run on CMSIS-RTX and Softdevice S110 and it doesn't have external 32K crystal.
The RTC os...
Hello,
I just received an NRF52DK today. I was able to run the demo (LED blink/Switch and NFC) which comes factory installed. But copying the hex files from demo (proximity...
