I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hi,
When creating and adding an characteristic to service, what the meaning and difference between these two variables:
attr_char_value.init_len
attr_char_value.max_len...
Hi all,
I have compiled the ble_app_hids_keyboard example for a nRF52832 on a Laird DVK-BL652 breakout board.
I have a tablet running android 5.1.1 and the nordic nRFConnect...
Hello All,
We are using nrf52840 board interface with wiznet550i.
We try to implement mqtt tls 1.2.we get following errors..
I get certificate verification error -0x2700...
I try to print the RSSI level but i couldn't do.
I use nRF51 DK and soft device S130.
This is the line that i just write:
SEGGER_RTT_printf("RSSI: %d\n",p_gap_evt-...
I'm trying to create a project from scratch that can use the S132 Softdevice, but I am constantly running into problems trying to get the correct headers, preprocessor macros...
Hello Nordic,
I am using the BL600 third-party module and SDK 10.
I was able to modify and compile project with GCC at
examples\ble_peripheral\ble_app_uart\ for s110...
As title,
I found that on the official website,
and I think it's extremely useful for someone(me) who need to measure the power consumption(current).
I can't find...
When I operate RESET PIN in main function like this:NRF_POWER->RESET = 1,Then cause a HardFault_Handler, (/attachment/fabd1141d36157d32f8c0353e4880b3e),What's this？
hi NORDIC,
is it possible to store float array in fds. i am able to store intrger values but unable to store float values. i am using example in this link :- github.com...
We have observed in couple of large size deployments that data packets from beacons that are bit far away tend to be corrupted. Devices that scan the signals from BLE beacons...
I have read the previous questions regarding the above subject, i found that changing the maximum bonding devices limit defined in device_manager_cnfg.h will work, but it...
Hello everyone, I must to write and read a I2C eeprom like 24c256. I tryed to do it but all the examples with I2C protocol works with 8bit addressing. I tryed to modify mpu6050...
Does the components on the development kit increase the power consumption compared to what you would expect from a low power-optimized application-specific PCB?
Other than...
I use the ble uart app to receive the data from mobile phone. The data packet size is 20 byte. If I transmit the packet one by one without adding delay, is it possible that...
HI,
Can anybody give me the connections to a BMD-300 with nRF52DK and the steps to program a BMD-300 from scratch? Which document provides the information, if there is any...
For ble_app_uart, if I write below routine to send data to mobile phone application. Can the mobile phone application receive all the packets without packet lose.
for(i...
my questions is in relation to BLE and the ability to sense RF at different distances using either dBi or RSSI(rather not use this), is there an accessable dBi signal strength...
