Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hello:
I was wondering about the random addresses programmed into the FICR on some of the devboards that I have. I read the devzone and it appears that the DEVICEADDR is...
I read that the DEVICEADDR is always in the advertising packet, so i need to take these data from the master each time that a slave is conected to them. I trying do something...
I'm using nRF52+SDK11.0.0+s132. In the ble_hrs PCA10040 example, the following are defined:
BLE_STACK_SUPPORT_REQD
BOARD_PCA10040
NRF52_PAN_12
NRF52_PAN_15
NRF52_PAN_20...
Similar to the thread posted here , I am trying to merge SD+bootloader+application and flash this to a nrf52 using the Segger programmer. This saves us a huge amount of time...
What is the best way to start a new nRF52 project, on a custom PCB?
I have a custom PCB, with nRF52 module. I use IAR, with ST-LINK V2
Say to test the GPIOs, do I start...
I took a look into the PCA10040 and the differences from PCA10036, seems to be minimal...
NFC connector and some breaking points. My question is: if somebody from Nordic...
Hi,
I am new to the nrf52. I want to implement the code that gives me current date and time value based on default set values.
for this i need to read the current counter...
Hi
Any ideas how best to implement a combined iBeacon and standard advertising device (both devices are active at the same time) ?
The iBeacon has to send an advertisement...
Is there a way to generate a DFU OTA image from OS X natively without having to use a Windows platform? It seems that the missing step is dat file generation and json manifest...
Hello guys,
Firstly, i would like to apologize if this post doesnt belong here. But i couldnt find any other platforms anywhere else for me to ask this question. So i have...
hi .
i did what this linke says
but it get me these error
..\main.c(632): error: #20: identifier "NRF_CLOCK_LFCLKSRC_RC_250_PPM_TEMP_8000MS_CALIBRATION" is undefined...
Hi,
I've got some really simple code I've been trying to get working with SPI on nRF52 (while also using SoftDevice):
///MISO, MOSI, SCK set, but SS not
err_code =...
I am trying to figure out if I need to disable the softdevice to get the power numbers in to the single-digit uA range.
With the softdevice loaded/enabled, but with the...
I'm developing nRF52832 to implement the Eddystone (※ 1).
But i'm thinking seriously about what can I do to have the Eddystone Specification and compatibility.
please...
