Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
We are having a slight issue when we are trying to update the DFU. The original version had this setting for the data reserve:
#ifndef DFU_APP_DATA_RESERVED
#define DFU_APP_DATA_RESERVED...
Hi everyone,
I have a nrf52-DK, I made samples with the saadc unit and i noticed there are unexplained peaks.
I connected the MIC's output (its VDD is from the board)...
Hi I bought quite a few of these on boards on e-bay and have worked a lot with them.
One thing that is confusing me is the variation in the number of retries, even when...
Hi,
I have tested a sample code which sends some data through BLE in nRF52 development kit(PCA10400). The code is attached below.
nRF5_SDK_11.0.0_MPU6050_Acc_X_Output...
I'm trying to compile the bootloader_secure example for the 10040 dev board using make, and it appears the makefile was not updated correctly with the changes made to the...
Segger RTT viewer is a great debugging tool. But every time when I download new firmware into my board I have to close the viewer and then open it after download is finished...
Hi guys,
in my application, I'm trying to do multiple fota, I succeed at the first time & after that I can jump again to the bootloader, but after that something is going...
I used nRF51822 IC and SDK11 with softdevice S130. I found a problem that our product cannot work. I dumped the hex code of 2sets from 0x00000000 to 0x0003ffff. One can work...
Hi,
I am using the nRF51822 module. I am facing problem to send multiple data formats packets over nrf module. I am using nrf SDK 11 version.
I am attaching my code with...
I want to start developing a Bluetooth device with the NRF52 DK. For debugging and sniffing purposes to see what is going over the air, use the NRF51 dongle, get a NRF51 DK...
In the nRF52 specification, I cannot find figures for the interrupt latency for event on GPIO pins in different power mode OFF, ON (constant latency, Low Power).
Can you...
Hi. I need to use direct advertising option in my application to minimize the time needed to establish the connection.
Firstly, I set up the connection during "normal" fast...
Dear Nordic Team,
Thanks for supporting.
I am try to work multiple (Peripheral) tag ID read with one central and stored in my PC via UART communication. Which example...
Hi,
I am new to nRF microcontroller and communication . currently, I am working on nRF51822 microcontroller. I am able to communicate between two nRF51822 microcontrollers...
