I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
I would like to set the the fstorage memory location manually through fs_init() within SDK 12.1, but I am not sure how to do this. There's comments that is can be done manually...
Hello,
I am using nrf52 and sdk 12. I compiled the code bootloader_secure from the examples in sdk.
Now I want to change the 16 bit uuid to 128 bit uuid in the code. The...
nRF51822CEAA
I am using a custom PCB, this is not a Dev Kit from Nordic
Mac OS X
Eclipse Version: Neon Release (4.6.0)
Eclipse Debug Configuration:
Specified arm-none...
I am using SDK_11 s130 on nRF51-dk. I ported the peer manager from ble_app_gls to ble_app_uart and enabled pairing without bonding.
Inside ble_nus.c, I modified rx_char_add...
Hi there, I have managed to set up my IDE and build environment so that I can build and download the example projects without any trouble, but have then spent the last two...
Hi.
I'm using SDK12.2.0, S130 ver2.0.1, nRF51822AC.
As I know SDK12.2.0 can conenct 8 peripherals at the same time when it is Central mode.
I want to use it as central...
I've got a custom NRF52 board that uses less than 4uA when sleeping without SPI but after the SPI is initialized (and then uninitialized) the current consumption rises to...
Hi Nordic,
For my application, I want to have the absolute acceleration (without gravity) from a MPU6050. I know that this device can do that because it has 6 axis and...
Hi,
I am trying to maintain a single bit of information through a power-on reset event (sd_nvic_SystemReset();). I am trying to do this through the configuration of an...
Hello,
I'm having problems running the DFU over serial bootloader example. The nrfutil command to update the application fails with message "timed out waiting for acknowledgement...
Hi together,
I'm trying to scan for BLE Beacons and I got the problem that if I set setReportDelay() to a value unlike zero, the onBatchScanResults() method is called and...
Hi,
I am trying to measure the current consumption on my application, and measured some quite high values even after calling sd_app_evt_wait().
After reading through some...
We have a product that uses nrf51422_CE_AA, Revision 3, 256KB ROM, 16KB RAM, PCA10028, SDK 8.0.0, S110. We have sold over 8000 devices of our first product. Currently we are...
Hello,
My problem is to much current c.a. 40uA in POWER OFF mode. Below attach code:
void power_down()
{
nrf_gpio_pin_clear(22); // Wylacz mostek tensometryczny
nrf_delay_ms...
