Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
i have dumped blinky example in nRF52832, in android mobile(nexus 5) i have downloaded nrf_connect application. connection is established but unable to recive any service...
This is a question for the developers of the nRF Connect Android app, or anyone else who might have the details.
The app has a really useful test hardness in it now that...
Hi,
I am working on implementing secure DFU. I have complied and loaded the secure DFU using gcc and am trying to upload a package using nRF Toolbox on android.
I have...
Hello Everyone,
I'm a beginner for nRF52 and my aim is to learn and develop system on nRF52. I have bought nRF52 development board and installed Keil MDK on my system....
Previously i've been using the nRF dongle using the BLE NUS Central example to communicate to another nRF DK with the BLE NUS Peripheral example via serial/termite and ble...
Hi there,
I am new to the nRF world and I might be asking a very stupid question with obvious answer but I couldn't find any hint from the Infocenter nor the Tutorials...
Hello guys,
I followed this guide to set up the software on my macbook.
The blinky example can be successfully built, but cannot be flashed to the nRF52 DK. Then I tried...
Hello everyone,
I tried to rename(right click the project name and click the "Rename") my project from "sdk11_ble_tutorial_adverstising" to "sdk11_ble_tutorial_adverstising1...
Hi,
anyone would have any idea (to look at, as to) why the same app running on the same chip/PCB (nrf51822QFAAH rev3) could possibly have slowed down so massively after...
I'm trying to add debug information to ble_app_hrs using nRF5 SDK 10, softdevice s110 version 8.0.0, building for an nRF51-DK target (PCA10028) using ARMGCC. I've found that...
I've encountered a problem getting the tick count from FreeRTOS when tickless idle is enabled. I'm not sure if this is a bug or just unexpected behavior. I am using the latest...
Hi everyone,
I'm integrating the spi_master_with_spi_slave example into our firmware; however, I'm not seeing the event callback I registered being called. I'm verifying...
Hi everyone,
I implemented nrf51 flashing through SWD (external MCU is used). After first flashing and reset when we enter debug mode on SWD second time we have a busy...
Hello,
I am trying to interface an MPU 6050 with an NRF52 with sdk vs 12.0. I noticed in the mpu6050.c file that it uses a twi_master.h file in the sdk in folder labeled...
Linking ble_app_proximity_pca10040_s132.elf
Output/nrf52832_xxaa/Exe/ble_app_proximity_pca10040_s132.elf section `.fs_data' will not fit in region `UNPLACED_SECTIONS'
...
