before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I use PCA10040 v1.1, Keil MDK 5.21a, SDK 12.1 with S132 v3.
I was using SDK 12 previously. The SDK 12 projects worked well.
Now I migrating to the new SDK. So...
Hi all, I'm working on SDK11.0.0 with softdevice S130 v2.0.0 and I need to update bootloader+application at the same time in single zip for these I created zip file by using...
I have a use for the pstorage module and while going over the implementations in the Nordic examples and libraries, I found a use-case of pstorage_register() in bootloader_init...
Hello,
I would like to use the PCA10028 close to the conditions of a future custom board at 1.8 V (including I/Os) but I would like to keep the ability to do source level...
I am using the 8.1.1 version of the SDK on a Rigado BMD-200 device, s110 version of SoftDevice.
The code has set APP_ADV_TIMEOUT_IN_SECONDS to the maximum (all bits set...
My main App must be able to use the soft device directly or serialisation when a external Connectivity chip is used. How can this be done? In the examples it's done at compilation...
Hello. i useing keil v4, s110 softdevice, nrf51822 ek boards.
I want to check my runtime.
So i use under the app_timer
app_timer_create(&m_heart_rate_timer_id, APP_TIMER_MODE_SINGLE_SHOT...
Looking at the nRF51 UART Example, i know that all packets transmitted over a BLE link will be protected by CRC on the link layer.
But how about when nRF51 scan the ibeacon...
Hi, I would like to use RTC1-> cc[1] using app_timer drivers. How to do this? Examples show only the usage of RTC1->cc[0]. RTC1->cc[0] has been used by ble_conn_params.c and...
Hi,
After few hours my program is crashing and I'm landing on address 0x1AFF4 which belongs to softdevice. For what is responsible this code and what could be a reason...
Hi
I am using Nrf51 and Softdevice S130.I know that softdevice S130 supporting Ble 4.2.This will act as a peripheral.My mobile phone supporting only Bluetooth version 4.0...
At s120,i used the following code to send data (to s110)
if( ( wIndicationFlag_Get() == true ) && ( wConfirmFlag_Get() == true ) )
{
//APPL_LOG("Write Data\r\n");
...
