Hello,
I'm looking for guidance and understanding of how to properly use the KMU and ITS for secure key storage of a key generated on device.
I see that typical ITS use...
Hello,
I'm currently using Visual Studio Code with the newest SDK, Toolchain and Plugin on MacOS and most of my applications are freestanding applications.
Now I want...
Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hi,
Can I use TI (cheap module 2451) as experimental blinky with central NRF52832.Don't need send button command , only UUID (TI:FFE0) check.It is possible?
Thanks
Hi all:
I download nRF51-ble-bcast-mesh from GitHub ,and put this project under below folder
...SDK8.1.0\examples\nRF51-ble-bcast-mesh-master\
compile this example...
I was doing power profiling using the PPK. All was working OK, as far as I went. I disconnected the PPK, and returned to normal debugging with stand-alone DK. Now I can't...
hi,all
S110 NRF51822 SDK8.0.0 server
i want to increase the througout speed,the SDK8.0.0 support changing MTU size?
MTU Can be in 4.0 protocol is modified?
if SDK8.0...
Hello,
I am starting to create a bootloader and I want it to be independant of the SoftDevice. Is there any open source implementation of a flash_write function that I...
Hi
officially for the nrf51 chip, 40 ppm frequency tolerance recommended but I'm not able to find this much of tolerance in digikey.
The only matching crystal digikey...
I am trying to get a NRF HRS central (ble_app_hrs_c) to make a connection to a NRF HRS peripheral (ble_app_hrs). However, the peripheral does not show up whenever the central...
It seems like a really great company, but after exploring and asking , and searching for a good BLE solution, I just can't find a good fit.
So you want a GOOD processor...
What is the Best way to send float over BLE?
Values range between -2.000volt and +2.000Volt (-2000mV / +2000mV)
Do I break it into two uint8_t and manipulate the +/- sign...
I am engineer, and I may be sensitive to user experience, or just a bad engineer but I do not get this.
I read ALL the guides available in the last 5 hours,
this
this...
Hello,
I have just migrated my project from sdk 9 to sdk 12.2....and of course from Device Manager to Peer manager. My initial project which was built off of the sdk 9...
During the webcast earlier this week, we were shown a phone pairing with the nRF52 dev board using NFC.
Is the code used for that NFC demo available as an example project...
Hi,
I am using nRF52832 as the core of my device that works with battery. I have to keep the SoC powered on all the time. When the off push-button is pressed I restart...
I am using a nrf52832 to communicate via UART to a GSM module (AT commands).
I have setup the device with a baud rate of 9600 and using HW flowcontrol. The nrf52 is doing...