Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
I am using IOS nRF Toolbox 4.2 DFU function on nRF51 DK PCA10028. I followed the tutorial here .
Use nRFgo Studio to erase all.
Use nRFgo Studio to program...
We have an nRF51822 peripheral device that is bonded with one and only one central. The central is always an iOS or Android phone running our app, which is scanning at "low...
In the BLE advertising library, in SDK 11, is the timeout for directed slow advertising specified in seconds, or in number of tries?
Seconds would be more consistent with...
Hi All,
I have got a project running on an nRF51422 QFAC, using the lastest SDK.
I am having some problems with the app_timers, i am able to create and start them, and...
Hello all,
i am working with the nRF52832 DK and SDK11. Actually the Enhanced Shock Burst Communication is working. I can send and receive messages. From this point on...
Lets say, that I've got a chip with program in its flash. I know I can protect it from being read back, but can I protect it from flashing anything else through debugger interface...
we have two nrf51-dks and we wanna create a ble mesh.
how can we set a ble mesh and same time ble advertising on Nrf51422 DK (PCA10028 V1.2.0) Board with using examples on...
Hello,
is there a possibility on nrf51 8.0.0 softdevice to determine whether particular notification has been received by remote device?
I use sd_ble_gatts_hvx() to send...
I am facing some problems with the app_timer api. In my application I have created two app timers. The timer api is using the swi1 interrupt for its working. I am using it...
During DFU with the nrf Connect app I get the error REMOTE DFU OPERATION FAILED. Here is the log file:
http://pastebin.com/y7hFNSBq
Using NRF5 SDK12 / NRF51 DK
...
Hi, Nordic
I have two nRF52 and one nRF24LU1.I want to use Gzp. two nRF52 pairs to the nRF24.
I use nRF5 SDK13 GZP device sample, nRF24 Gzp host sample.
But only...
Hi
We are very interested to test the wireless range using Bluetooth 5, 125 kbps long range mode.
If we purhase two nRF52840 Preview DK boards, is there a easy way to...
Hello,
Currently i am doing some testing with the NRF52 DK.
I am measuring the time it takes to send and receive a BLE message.
I am using the high bandwidth setting...
Hi all,
Someone can give me a information about the difference between function uint32_t err_code = sd_ble_gap_adv_stop(); and stop the advertising with using the timeout...
hi everyone i'm using 9 axis imu sensor with the nrf51822 board and i'm confusing in how to calculate the roll,pitch and yaw values,can you please suggest me some methods...
