Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
I have a nrf51-DK, SDK 9.0, S110, dual-bank bootloader that supports both serial and ble protocols, developed using GCC/Eclipse. My application uses the watchdog timer. I...
Hi,
I'm developing an Android application that uses Android DFU Library and I want to set the number of packets that are sent every notification interval to 1. I couldn...
On the BMD200 evaluation kit ( www.rigado.com/.../) using the nrf58001:
--> UART TX (pin P0.09) works - confirmed with logic analyzer and Serial Port Terminal on the PC...
We are operating on nRF51822 QFAC with S130 SD. We have a functionality where the device switches between scanning and advertising. Strangely we have observed that after few...
Hi,
When i read the ble_peripheral sample of the SDK, i have a question below.
If my peripheral is connecting a central, then i use function sd_ble_gap_disconnect() to disconnect...
Hi,
The established time tick source for FreeRTOS is RTC1 via the APP_TIMER module. I am trying to shift the basis of the APP_TIMER from RTC1 to TIMER2, so that I can use...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
Hi,
I have an nRF52 dev board (PCA10040). I have been using this board for measuring current. I am using the Keil tools.
Yesterday I made a change to main.c in the ...
Hello,
I am working on S120 v2.1.0 and SDK 9.0 for central and I am able to connect to my iPad. Now I need the central to delete the bonding information stored using pstorage...
Hi All,
I am wondering if I could upgrade from S110 to S130 over the air.
What I see in the S110 and S130 hex file is that the MBR is different. Not many bytes but it...
I see that there is a 1.2 Volt VBG reference available for the ADC but that reference doesn't seem to be available for the low power comparator. Is there any undocumented...
I'm developing a central providing NUS client services to multiple concurrent peripherals. I had code working reliably under SDK 9.0.0 based on the NUS client example in github...
Hi, we looked at your BOM for matching components in your file:
www.nordicsemi.com/.../15787782
for QFAC variant of the IC. You use LQP15MN27NG02D as 27nH inductor which...
Hello guys,
I am using this repo to update my device's firmware but after the update is complete, the iPhone cannot find the correct devices services anymore.
To detail...
We're using the NRF51822 and the S130 with V9.0 SDK, and we're using most of the features of the SDK for our Firmware; but I'm running into a problem flashing the device on...
