Hello Nordic Support,
I am developing a cellular positioning solution using an nRF93M1 LTE Cat 1 bis module.
I currently use the following command to retrieve the serving...
Hi,
We are experiencing a low RSSI/range issue with our nRF54LM20 module using the nRF21540 FEM.
We have already consulted with you regarding the design under Case ID...
Hi,
I have encountered a challenge with the nRF54L15 that I am hoping someone might know a solution for!
My device has a power enable pin (on GPIO1) that must ideally...
I am using the SDK v3.4.0 LTS
for modem error debugging I included: prj.conf
I am mapping errors depending on wether memory allocations failed.
I am fetching the stats...
If a Channel Sounding procedure is aborted while in flight and the ACL is then disconnected, the device settles at a flat ~1 mA with the CPU asleep in the idle thread and...
Hi,
I am developing firmware on the nRF93M1 DK and have a question regarding the Wi-Fi location feature. According to the Nordic documentation (Features of nRF93M1 — nRF...
Hello all,
I am looking to hire a developer experienced with ANT+ together with BLE and the nRF52840 SoC, possibly the nrf54L10.
I am looking for the coding for the...
I have two nRF9151 DK boards, both hardware revision 1.4.0, both showing the same SIM detection failure.
Symptoms on both boards:
AT%XSIM? always returns %XSIM: 0,9...
We have purchased a radio fitted with the nRF9160 modem and fitted it with a roaming SIM for NB-IoT use, we are in UK and have Band 20 EE and Vodafone.
What are the initial...
Now my product need FCC, and I use DTM example, only changed the txd,rxd pin in firmware, the lab can use nrfconnect for desktop to enter test, but the tx power is low when...
Dear Nordic,
I'm designing a 0.6mm thick 6-layer rigid-flex with the nRF54L15-CAAA, and due to my current stack-up the ground polygon to trace clearance can only go as small...
Hi Nordic Team,
Could you please clarify the SDK/NCS compatibility for the nRF54L15-CAAA chip?
We are planning to develop firmware in bare-metal mode and would like to...
Hi For a product, I'd like to have (well it's a requirement) the firmware update encrypted. So I set the following in sysbuild.conf: ... SB_CONFIG_BOOT_ENCRYPTION=y SB_CONFIG_BOOT_ENCRYPTION_ALG_AES_256...
Summary
On a small fleet of identical nRF52832 units running the same firmware (NCS 2.5.1, SoftDevice Controller, BLE peripheral, LFCLK = RC with calibration), individual...
I want to implement a BLE composite device with BLE UART and BLE HID, and both services can work at the same time.
Hello! I want to make a Bluetooth game controller, and...
Dear Nordic Experts.
We designed a device based on the nRF54LS05B module.
We are writing a production test program and using nRF54LS05-DK Rev 0.3.1 for verification. ...
We are using monitor mode on the nRF7002 to receive packets in promiscuous mode. We are on NCS 2.9.1. The Wi-Fi packets we receive have the follow header (struct copied from...
The nRF Thread Topology Monitor is a very useful bit of software. It would be very nice to see it updated, or perhaps even made a first-class member of the nRF Connect for...
Can you pls send recommendation document for the exact foot print to be used for nRF54LM20A-PAAA CSP98 BGA?
I have found reference foot print BGA98N35P10X10_385X367X68.dra...
Dear Nordic team,
we are evaluating the nRF9151 for a data acquisition application/device. Our first goal was to get the official HTTPS client sample to run on the nRF9151DK...
Hi
I am developing RX device to connect with Smart Remote 3.
The RX device system is Linux embedded. I need to run OTA function in Linux embedded to update SR3 F/W.
...
While debugging the code with Nrf connect extension in VS code , code get stuck at the start only does not go any where getting the SIGNTRAP error continuous
