Hi:
I use sdk ncs3.3.0 and nrf54lm20dk.
Failed to return using AA dfu_target_init.
OTA firmware is zephyr.signed.bin.
I: DFU header I: 3d b8 f3 96 00 00 00 00...
Hi there,
I'm evaluating the latest release of NCS ZigBee addon version 1.4.0, wanted to try and migrate my existing project to the newer version. I've encountered the following...
Hello,
I've been asked to create a new ticket for this. It follows on from
@ Erlend Isachsen asked:
So before marking this problem as resolved, it would be nice to be...
I am developing on the nrf9151 with SDK v3.4.0.
The device I am developing will be moving trough all of europe . My goal is to speed up the `AT+CFUN=1` conenction part of...
HI
I am currently carrying out secondary development for PAWR based on NCS 3.2.1. I understand that its communication adopts frequency hopping. I would like to ask whether...
NCS-3.4.0, on nRF5340, custom board losely based on PAN1783. No RTT backend, BLE stack works properly:
RTT enabled, BLE stack reads some garbage:
Printing is done...
Hello, our design does not use the USB block of the 52833. In the electrical schematic we have connected VBUS (AD2) to GND and we leave D-(AD4) and D+(AD6) open. Due to a...
In my project an interacting with the ncs 1.6.1 peripheral _uart example and my plan is to ensure that data size being send at a particular time is increased to send at least...
Hello everyone,
I went through the forum and saw some topics regarding the implementation of the characteristic read out over sd_ble_gattc_read. I implemented it as desribed...
Hi all,
I would like to know, if any example code available for AoA algorithm for ble direction finding. I am working on a project for indoor positioning and tracking...
Hi,
I am trying to sample a large quantity of sensor data from the nrf52840dongle as the server and the nrf5283dk as the client. I have used the peripheral uart and central...
Hi all,
So I want to give you a full description about what we are doing because we could not understand what we did wrong.
Our DK : dk-51
Soft Device : S130_v1
Our...
Description:
I try to initialize a SPI device in my nRF52DK through the Zephyr‘s driver(drivers/spi.h).
Code seems correct when compile and I got no error when build the...
Hi, I am new to Zephyr and Nrf, I am trying to replicate the event manager arch from asset tracker v2 but I am stuck in the setup. I am trying to use the logging capacities...
I am working on the Electronic Braille Display for visually challenged persons.
Our device will communicate with Voice over service on the laptops and smart phones using...
Hi,
with %SHORTSWVER: nrf9160_1.3.1 I am getting:
AT%CMNG=0,3,4,"test1234" OK
AT%CMNG=0,3,3,"30313233343536373839303030303030" OK
AT%CMNG=1 %CMNG: 0,6,"0606060606060606060606060606060606060606060606060606060606060606...
I have a single sample of the new nRF52840_XXAA at hand on our custom board. I'm trying to do a --recover with nrfjprog. As the log below shows, nrfjprog recognizes it as...
Hello ,
I m using SES v5.6 and NRF52805 ,ble_app_uart ex (nRF5_SDK_17.1.0),
Requirement -need to wake up and reset ( or start advertising again) from sleep mode ,when...
Hello,
I have adapted some of the ESB proprietary Protocol from the NRF SDK into my own project without installing the SDK directly; however, complete integration seems...
Hi Team ,
In my application , i am using RTC1 for RTOS and RTC2 for Running a time calibration andRTC0 for Softdevice but parallelly i need to add Lbs service which includes...
Hi there,
I wanted to test Matter/Thread networks using the nRF5340DK I have.
I downloaded the nRF Connect SDK through the Toolchain manager.
I tested the blinky app...
Hi,
I have an unusual requirement where the current constraint device needs to the controller and passively scan. My understanding is the best way to estimate the current...
