I am unable to perform a fota on an nrf9160 based device in the field since my nrfcloud account was updated to require the use of the new memfault based version. There was...
Hi,
I just read the nrf54l15 errata [100] of the nrf54l15. It's actually a huge issue, as we do have an interrupt line on one of the affected pins, that is active low, eg...
Hello, We're in EMC testing for a host product built on the nRF9151 (LACA A1A, FCC ID 2ANPO00NRF9151), running modem firmware mfw_nrf9151-ntn 1.0.1.
For our lab build, we...
Hello:
Hello Nordic Support,
We are developing a battery-powered product based on the nPM2100 and nRF54L15 , powered by either a CR2032 or CR2450 primary coin-cell battery...
We are using the nRF54L15 chip in a new product that is essentially a sniffer. We periodically turn the receiver on for 5 to 10 seconds to sniff for BLE advertisements from...
Hi. After I modified the function static void ranging_data_cb(struct bt_conn *conn, uint16_t ranging_counter, int err), I exported the IQ data, as shown in the figure below...
Disclosure. I am new to firmware develoment. My experience is in cloud development.
I just bought a Thingy91. I registered online using nRF Cloud. The modem communicates...
I want to use a timer to get a fixed time interval, so I use a 32-bit timer to count from 0 to 10000, and use PPI to clear the counter when it is captured to 10000, such as...
I'm using Softdevice S132 V 7.0.2 with nrf52832 module. Project is in Segger Studio. Project runs in debug configuration as in debug or in non-debug mode. When changing to...
Hi, I want to run hci_usb as a USB dongle, and use the CONFIG_BT_LL_SW_SPLIT software based link layer controller on nrf52840dk
But somehow once config as CONFIG_BT_LL_SW_SPLIT...
nrf_ble_ancs_c.h has hardcoded max attribute length of 32 (BLE_ANCS_ATTR_DATA_MAX).
1) BLE_ANCS_ATTR_DATA_MAX mainly seems to be used to allocate the size of the app_id...
I'm working on an nRF5340 based design and using the nRF5240DK to get started.
I would like to have an immutable first stage boot loader, an updatable MCUBoot boot loader...
Are there any suggestions for creating slightly customized versions of the immutable and MCUBoot boot loaders?
Currently I'm using CONFIG_SECURE_BOOT=y & CONFIG_BOOTLOADER_MCUBOOT...
I would like to include the MCUBoot library code into my application so that I can read and validate update images (before restarting the MCU to install them via MCUBoot)...
I have a custom MCUboot boot loader working. Now I'm trying to build an application to be updated by MCUboot. I've added the following to prj.conf:
CONFIG_BOOTLOADER_MCUBOOT...
I am running a NUS at 115200 Baud and it works fine but when I run it at 921600 my BMD 300 triggers a Serial Fault. Is there a trick to get the 921600 to work without flow...
Hi Guys,
I need to connect to a BLE device using NRF52480 using passcode (6 digit pincode)
on Android it works just fine, I attempt to connect and displays the popup...
led 1 is off but p0.13 get 3v output , similarly led 1 is on p0.13 get 0v output, how to change it help me. similar for led 1 to led 4 respectively p0.13 to p0.16.
Hi I am the user of zephyr and nrf connect SDK in ubuntu 20.04. one question about file path in the header file. for instance, the demonstration "nrf/samples/zigbee/light_switch...
Hi, I tried establish a communication between nRF52832 DK(PCA10040) to nRF24L01+ Module with Arduino UNO(via SPI). I used the EnhancedShockburst examples from nRF5 SDK 11...
Hi,
I'm developing a GUI on Qt creator to communicate by USB (send and receive data) with a nRF52840 DK. For that, I want to use the USB CDC ACM module (instead of UART...
