I'm develping my application with nrf52832 and nrf SDK v17.
I'm testing SPI interface so that I can use the external flash.
When I using SPI without BLE stack,the waveform...
I'm developing with an NRF52832, using NCS v2.6.1/Zephyr 3.5.99
My custom hardware has three NXP PCA9538 GPIO expanders on it, to allow me to control various address and...
I think this code snippet is causing the issue, since I am able to make the device work by setting:
' NRF_SDH_BLE_PERIPHERAL_LINK_COUNT = 1' and 'NRF_SDH_BLE_TOTAL_LINK_COUNT...
I am working on a project where I am using the npm1300 with host nrf5340. The BUCK1 powers a sensor and BUCK2 powers the nrf5340. I have a SPDT switch connected to GPIO0 and...
Hi,
Is it possible in BLE channel sounding in ncs 3.0.1 to get some information about the quality of the distance measurement for each method? We have three ways to get...
Hi,
my name is Nick De Leenheer, and i am finishing my thesis on indoor localisation with CHANNEL SOUNDING. i currently got these outputs in my venv using SERIAL: so i...
Hi,
I´m working on a Zigbee-based environment sensor. You can find all related files here: https://github.com/Kampi/BeeLight
Now I have the following scenario: the whole...
Hi,
I am struggling with a low power consumption solution for waking the NRF52832 with our product which is using a third part module.
Currently our product total power...
Hi, I have Lenovo tab E8 tablet with Android 7.0 and I connect to a BLE device (nrf52832 SDK 15.2.0 S132) from my Qt 5.11.2 app. After succesfull connection I discover services...
The toolchain setup of the NRF91 is extremely complicated. Is the a VM Image or Docker container that has everything pre-configured? I am trying to setup up a linux VM now...
I have a 52840-DK (PCA10056) connected over USB on Windows 10. I am using IAR and can build and run demos from EW in this configuration but am having no success with nrfConnect...
I am working on a project on the nrf52832 board using mesh SDK v3.2.0 and SDK v15.3. I am trying to troubleshoot an issue with the publish process for BLE mesh, but I am not...
Testing DFU with IOS version of nRF connect. I am able to save my image to the IPad with Itunes. I can select the file and then start the DFU process.
Process completes...
I am trying to setup a VM (Ubuntu 19.04) that has the complete setup for NRF91 development. I have been following the instructions in the nrfConnect 3.2.0 - getting Started...
Dear Support,
In our new project, we have 8 signal LED diodes attached to nrf52832, they are all sinking current:
3x GREEN 0.8mA (P0.16, P0.17, P0.18)
1x RED 3.3mA...
I am trying to setup a VM (Ubuntu 19.04) that has the complete setup for NRF91 development. I have been following the instructions in the nrfConnect 3.2.0 - getting Started...
Hi,
I'm using SDK 15.2. I flashed the dtm firmware on the BLE chip. How can I test its working before sending it to the certifier? I have nrfgo studio & I'm able to start...
Hi Team
We are able to flash nRF52840 based LE Module using nRF52840 DK successfully.
But we would like to know if nRF52 DK also can be used to flash/program this nRF52840...
Hello,
SDK:15.3
If not pair with moblic phone, spi is normal
And obile phone pair 52811 to send data, that also normal
But I want to integrate, then 52811 is NRF_BREAKPOINT_COND...
Hi all:
For SDK15.3, if I want to change 32.768Khz to internal LF clock, Should I enable the CLOCK_CONFIG_LF_CAL_ENABLED of "sdk_config.h" ?
if I disable CLOCK_CONFIG_LF_CAL_ENABLED...
