Hello,
Context : I use the nrf52dk with nrf connect for vscode and nrf connect for smartphone (android last version). I use the last version of everything.
My code to...
Development board: nRF54L15DK i I'm already using "Find My Example" to connect to the "Find My" app on my iPhone. At the same time, I also want to connect to nRF Connect....
Hello,
I am trying to modify peripheral_hids_keyboard 's security configuration as Security Mode 1 Level 2.
According to some Q&A thread, I tried the following:
1...
hi support team,
if customer want to certificate device with 21540, which tool can customer use for dtm testing?
our tool can only set it to 8, can't be 10, as below:...
I'm developing with an NRF52832, using NCS v2.6.1/Zephyr 3.5.99
My custom hardware has three NXP PCA9538 GPIO expanders on it, to allow me to control various address and...
I think this code snippet is causing the issue, since I am able to make the device work by setting:
' NRF_SDH_BLE_PERIPHERAL_LINK_COUNT = 1' and 'NRF_SDH_BLE_TOTAL_LINK_COUNT...
I am working on a project where I am using the npm1300 with host nrf5340. The BUCK1 powers a sensor and BUCK2 powers the nrf5340. I have a SPDT switch connected to GPIO0 and...
Hello Nordic.
I find two RNG example.
Both nrf_crypto_rng_vector_generate and nrf_drv_rng_rand , what is the difference?
Which one is better on RNG.
How to correspond...
I am trying to set up developing environment, and however I couldn't download and install version 7-2018-q2-update of the GNU ARM Embedded toolchain.
Would you please guide...
In my application i need to use NBIOT network & GNSS.
For that i found that i need to configure AT%XSYSTEMMODE=0,1,1,2.
But i am not clear on what should be configuration...
Central info SDK: 15.3 nRF52840
Uart communication is used. In rare cases, the value obtained by checking the waveform with an oscilloscope was different from the value...
Hello everbody,
I readed alot about the nrf52480 "how to flash softdevice and the other stuff", but i cannot get the ble_app_gls working out of the scratch.
I have the...
Hello everyone, I am trying to implement audio processings algorithms with my nrf52DK.
What i need to do in order : 1- Sample my audio signal ( It will be guitar sound ...
I need to use a nRF52 chip to handle interrupts with low (and known) latency. Basically, there are specific ~100 us long intervals during which I need interrupt latency to...
I am trying to setup a VM (Ubuntu 19.04) that has the complete setup for NRF91 development. I have been following the instructions in the nrfConnect 3.2.0 - getting Started...
Hello Devs,
I am using app_timer to create multiple timers to read different sensors
Currently, I have 5 timers created using app_timer_create, each timer has their own...
I use nRF Connect for Desktop to download hex file(nrf52810).
Use the following example：
nRF5_SDK_15.3.0_59ac345\examples\dfu\secure_bootloader\pca10040e_ble + nRF5_SDK_15...
Hi,
How do i turn off the nrf power management library? Is there any function like nrf_pwr_mgmt_uninit()?
The reason i want to turn it off is because it causes the usbd_msc...
I have a requirement for BLE and 802.15.4 stacks in a multiprotocol environment. I have looked at the sample at NordicSemiconductor/nRF-IEEE-802.15.4-radio-driver on github...
I am trying to initialize the RTC and trigger an interrupt every 10 seconds, and I am unsure of why the code above is not working. I followed a similar method to initialize...
Hi,
I'm working with the nrf52840 and spi mngr to talk to a SPI flash memory (AT25SF081). I use nrf_spi_mngr_perform to send a command to read the manufacturer ID
...
