Hi, We're in the product validation stage of development with nRF54L15, part of the validation is temperature cycling, we noticed that devices seem to be "stuck" in sleep...
Hi,
I am trying to configure an Xiao Seeed Studio nrf54l15 sense to transmit pre-processed sensor data via BLE extended advertisements. As the payload is more than 251 bytes...
In this post mentioned: "Maximum theoretical peak data rate is 3.4 Mbps when transmission is scheduled into packets of 4 slots using MCS4, and these 4 slot packets are transmitted...
I want to use a new source LF clock to raise the precision from +-250ppm to around +-20ppm. I already have an oscillator mounted in my PCB, so I want to use it for BLE. I...
Hi,
I would like to know if its possible to run Azure FOTA functionality w/o using Partition Manager (aka `SB_CONFIG_PARTITION_MANAGER=n`) ?
Trying to build this gets...
Hi Nordic team,
I have a question regarding the RF matching networks used in the nRF54LM20A-PAAA reference design and in the nRF7002 Expansion Board II (PCA63571).
For...
In the absence of a QGAA reference, is there anything to be aware of when designing a QGAA board?
For example, with the nRF52840, the WLCSP and QFN references used different...
Our nrf9151 boards are getting stuck when nrf_modem_lib_init() is called.
We just see this line. Usually, the device gets past it in less than a second.
[00:00:00.376...
Hello, I measured with the PPK2 over the weekend and it stopped updating the .raw temp file after 208,201 seconds (probably nothing special about it) It is around 12GB. The...
Is there a BLE development board that supports extracting IQ data from raw MCPD ranging？ Does nrf5340dk support users to extract IQ data for the development of ranging algorithms...
Hi!
With the release of NCS 3.0.1, the required SEGGER JLink version to v8.18. pynrfjrprog is bundled with SEGGER JLink v7.94. From your website, it seems nrfjprog, being...
Hello,
I have designed this schematic according to reference designs provided by Nordic Semi, however I might have failed as I am unable to flash the main module. I should...
Hi,
We are planning to move with the nRF5340 + nRF7002 for our upcoming project. We would like to know, whether the nRF5340 supports any camera interface. If it support...
I am currently trying to get LLEXTs to work on the nRF5340 Audio DK. I was able to compile an llext and load it successfully, using the cmake features, However, I would like...
Hi, I would like to consult how could I deal with this error and build the code succesfully.
In device.h
'__device_dts_ord_113' undeclared here (not in a function); did...
Hi, I have two firmware images: A and B which I need to make compatible for OTA (DFU over BLE using MCUBoot - the standard process described in the devacademy course ). They...
I have used the Programmer previously with success. I am attempting to program the Dongle (10059) with a slightly modified version of ble_nusc_usb_dongle. Although it claims...
The Matter stack’s auto-generated file ` access_buildconfig.h` explicitly sets ` CHIP_CONFIG_USE_ACCESS_RESTRICTIONS` to ` 0` , overriding my attempts to enable it. This prevents...
Hi Support team:
I am new for using the Nordic Design kit of nRF54L15-DK.
And I would like to use the app "Direct Test Mode" v2.4.2 built-in the "nRF Connect for Desktop...
How do I preprocess a C file (typically done by passing the "-E" option to the compiler) in VS Code with nRF Connect SDK 3.0.0 or later? I want to see how a complex macro...
I built the littlefs zephyr example found in "/zephyr/samples/subsys/fs/littlefs"and then modified it to use the external flash "MX25R64" by adding an app.overlay file. I...
