Hi
I have a question regardin why nRF54L15 cannot use the automatic mpsl power split?
If I want to use ESB + nRF21540 with automatic TXP control, what should I do?
Hi,
I have a PCA10040 and use nRF5_SDK_17.1.0_ddde560.
I build this example project in Segger Embedded Etudio and it works fine and I can load elf file and debug etc...
Hello,
I'm going through the documentation to understand the available tools better.
And in Section 6.2 CPU of the latest nRF5340 Product Specification v1.6 it mentions...
NRF54L15 with 3 shared spi devices, not working.
I have a custom NRF54L15 based board with 3 spi devices, all sharing the same SCK / MISO / MOSI lines.
SCK = P2.06 MISO...
Hi,
I have a couple of questions on migrating from Partition Manager to Devicetree since a particular example was not provided. Following the procedure in the SDK v3.3.0...
Greetings,
Although multi-NUS is not officially a sample in the nRF Connect SDK, it is closely related to nrf/samples/bluetooth/central_uart, and I thought it would be...
I have tried several code samples: nrf/samples/bluetooth/peripheral_uart and nrf/samples/openthread/cli. If I set hw-flow-control in zephyr/boards/nordic/nrf9160dk/nrf9160dk_nrf52840...
Hi,
I have been hired to migrate an NRF51 project that has S310 to an NRF52 one on S332.
I have looked at the migration guide in detail and had some follow up questions...
Hi I am having a hard time implementing DFU using SDK12.3 / nRF52832 now. I have tried so many times, but have failed a lot and have left a log similar to the next one in...
Hi,
I am using v0.4.0 ncs sdk.
I added following in the nrf9160_pca10090ns.overlay file
I added following in the prj.conf file
I added following in the...
I made a Windows application that makes USB connection with nRF52840. You need nordic_cdc_acm driver to use it with windows 7. Can I distribute the nordic_cdc_acm driver with...
Is it possible to route a signal derived from internal clock to an IO pin? I am new to NRF micro controller. My experience has been with Cypress PSOC and in the IDE it was...
I am trying to implement a struct that will be saved in non-volatile memory. Does the dev kit have these capabilities on its own? If it does is there a guide on how to use...
Hello,
I am using secure dfu with bonds (SDKv15.3, Segger, nrF52832), it works fine however after each dfu (application only) I lose the bond information.
I have search...
I am trying to communicate with PN7150 from nRF52840 DK using I2C pins.
PN7150 needs 3.3V and nRF52840 is supplying 2.9V.
I am able to read PN7150 on Arduino Mega but...
I made a Windows application that makes USB connection with nRF52840. You need the nordic_cdc_acm driver to use it with windows7. May I distribute the nordic_cdc_acm driver...
Hi Nordic,
We're developing a product based on the nRF52810 and got the following question:
We were wondering if we can recover a board in the worst-case scenario where...
Dear all, My team want to develop a innovative product. I am following this tutorial ( www.youtube.com/watch to enable the CMSIS Configuration Wizard in Segger Embedded Studio...
I am working with SDK15.3.0 and a PCA10040 with S132. I have two questions relating to the BLE addresses as seen by the PCA10040 and by nRF Connect.
Q1 - What is the relationship...
Modem firmware version 1.0.0
Segger version v4.18
nrf tag v1.0.0
Often when I try to flash a new build of an application and try to flash an application through Targert...
Dear Team,
I want to integrate an nRF chip into my Project. I will use a ready made module from Laird, the BL652-Sx.
For Debugging I want use the nRF52 DK and connect...
