Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
I recently completed a field-upgrade path from an nRF5 SDK 17.1 application (with the legacy Secure DFU bootloader) to a fresh NCS-based firmware stack, while preserving user...
Hi, I am trying to understand the Friend and LPN behaviour. For that I am refering to nRF sample application light" and "light_switch". Below is the setup details: 1. On one...
I using 3 nRF52840 DK borads (provisioner,light_switch_client, DFU). I set DFU (DFU example used) as target board and connected it to PC as serial interface. I have provisioned...
Development Software: SES v4.16
Computer Platform: macOS v10.14.4
Hardware: nRF52832QFAAB0
Hello, everyone~
I feel confuse that how to make the Complete Local...
Hello,
We are using nRF52840 and Thread SDK to build a mesh network. At present, we only need to transmit data frames. But, in the near future we would like to transmit...
Hello,
Im trying to boot into a custom bootloader following this documentation .
Under "programming the bootloader" it says you must write the bootloader start address...
I have some question about direction finding in BLE5.1.
1. Does the 52840 DK support nRF52811 Soc? if not, Is there any Development kit support nRF52811?
2. Does the AOA...
I called several distributors but they say they don't have a way of differentiating the revs. Please let me know where to order and if needed...how to order please!
Hello there,
I'd like to send and receive data through NRF Radio's handler. I've been able to configure the handler to receive data. Otherwise, I'm having difficulty on...
Hi all, I have some question.
When I using mobile to bond with my DK nrf52832. Infomation will save to flash via FDS library.
So, when I delete bond from mobile and rebond...
Hello
I am using ble_app_multilink_central on nRF52832 DK.
I want to collect advertising data from all peripherals and not connect to them. Problem is that I dont know...
Hi guys! I have had an issue with Image Transfer Demo project. I use nRF52832 with OV2640 camera. I used installation project process described on the page https://github...
Imagine i have a client which sends message to a gateway and i set a TTL for the shortest path . If one of the node is not functioning how will the mesh reroute the message...
nrf52840
sdk for thread and zigbee 2.0
windows
segger studio
in example simple coap cilent and simple coap server
I create my own packet error test through coap...
Hi All,
Currently in my project i'm using hard core delay and delay is custom i.e some places i have used millisecond and in some places used microsecond and in sec.But...
Hi all,
I may need some guidance on the finite state machine method which found an example in app_level.c (from nRF5 SDK for Mesh v3.1), please see my question on below...
What is the minimum specified voltage required on ENABLE (Pin 101) for proper operation of the nRF9160 SIP? Is it the traditional 0.7 VDD, or is it permissible to use a lower...
