Hello,
After I upload a new signed image to my device using MCUboot serial recovery (single image), MCUmgr Img_mgmt_client API
img_mgmt_client_state_read() always fails...
Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
Hello,
I am working with a custom board that has the nRF52840 (via the ISP1807-LR-RS module). This board has the SIT1552AI-JE-DCC-32.768E MEMS TCXO. This TCXO chip has a...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
I flashed the mesh serial hex file in two dongles and used one dongle for connecting it to the nRF Connect Windows application. The hex files were present in the nRF SDK for...
Dear Sir,
Whitelist(on periperal side) are used for filtering scan requests( onlly allow the scan requests from the devices whose address is there in the whitelist with...
I'm using ble_app_uart example.
The board go in low power mode, but after 3 minutes (#define APP_ADV_DURATION 18000 ) go OFF. I need that remain in advertsing mode always...
I was developing an green house system for plants which was based on nRF51822 SoC. The system was fully completed and working fine except one problem which was reset of nRF51822...
I am trying to find the optimal way to automate some tests that I run on my BLE device. In this test, I need to write a specific hex value to a custom BLE characteristic of...
Hi all,
I am working on a project and use DWM1001-Dev. I think some of you may have an opinion about my problem because DWM1001 have nRF52832 microprocessor. I'm trying...
Hello,
I'm trying to change the BLE local name from the application before rebooting into the secure bootloader.
I've noticed that I could use the nrf_dfu_set_adv_name...
Hello all,
We got the fail situation and we tried to find the solution to fix it.
Our develop situation :
nrf52832/SDK 12.2.0/Windows
Our products already went to...
Hi, I have some question need your help.
I use SDK 14.0.0, S132 and peripheral code. and then I define two peripherals of function in the nrf52.
Q1: My product needs bonding...
NRF_SDH_BLE_OBSERVER(m_ble_observer, APP_BLE_OBSERVER_PRIO, ble_evt_handler, pContext );
evidently I register here a callback "ble_evt_handler" to the softdevice for ble...
[development software, with versions]
nRF5_SDK_for_Thread_and_Zigbee_v1.0.0
RaspPi_OT_Border_Router_Demo_v1.0.0-1.alpha
NCP example located in <InstallFolder>/examples...
Hi,
I am working on a project that I need to trigger a device (Coded with c language) through beacons. Is there any example code or functions I can leverage for these purposes...
I am developing Beacon using nRF52832, I want to send advertise using different Channel numbers.
To implement Channel Diversity I want BLE to transmits in three advertisements...
