My DECT nr+ PT supports connecting to either of a set of networks, which of course have different integrity and cipher keys.
While scanning for cluster beacons, I can receive...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
I recently completed a field-upgrade path from an nRF5 SDK 17.1 application (with the legacy Secure DFU bootloader) to a fresh NCS-based firmware stack, while preserving user...
Hi, I am trying to understand the Friend and LPN behaviour. For that I am refering to nRF sample application light" and "light_switch". Below is the setup details: 1. On one...
Hello,
I have cloned the asset_tracker project and would like to add the Zephyr Shell to it. There are no clear directions on how to do this. Can you point me to instructions...
Hello nRF world,
We have custom peripheral board based on the nRF51822 and need to be able to pair it with a host. Does anyone have a well documented example of code for...
Hello Nordic ,
Do i need to implement the config_ client model so that the node can be named as a client and a provisionner in same time ???
however in the example of...
I am using SDK 15.2 with IAR's EWARM 8.30.1 and the nRF52840 Development Kit. My eventual target is the nRF52-Dongle. If it matters my development OS is Windows 7 64-bit....
I would like to write code to disconnect from any connected device. My system is a ble peripheral with s132 6.0.0.
My code calls:
result=sd_ble_gap_disconnect(BLE_CONN_HANDLE_ALL...
I starting working with examples for the nRF9160. Zyphr seems like a very complicated OS (like Linux with device trees, etc) and difficult to use with a debugger.
Is the...
Hi,
I trying to convert a stm32 function code to nRF52. The goal is to use a spi periperal on my custom board.
In this application we need to have 2 bytes transfert. That...
I can communicate with success from the pc to my custom nrf52832 device (SDK 15.2, S132v6.1) using the pc-ble-driver (sd_api_v3) with Tag 4.0.0 from Github. Great work!
...
Hi,
I designed a nRF52832_xxAA board, use an external power switch, without DFU features its operating normally.
When I add the DFU function according to the Sample code...
Hi,
I am using nRF51822QFAA-R7 controller(DC DC setup) in my design.
I am generating +3.3V from rechargeable battery and providing +3.3V as a supply to drive these controller...
Hi,
I'm just getting started with nRF mesh (sdk V3.00) and I've built the light switch sample successfully and deployed it on three nRF52832 development boards but provision...
hello,nordic
I use NRF52840 QSPI+FatFs+USB-msc(..\nRF5_SDK_15.2.0_9412b96\nRF5_SDK_15.2.0_9412b96\examples\peripheral\usbd_msc),I found there is a bug about write to flash...
I am working on a new design for the nRF52832. I need to match an antenna to the device. My understanding is that the output impedance of the nRF52832 is 53 + J66 for best...
