I checked the nrf52832 manual and found that both XC1 and CX2 are analog input pins for the 32Mhz clock pin configuration. The reference design for both uses 32Mhz crystals...
Hello, I’m working with a custom board using nRF7002 + nRF5340 + MX25R64 (SPI4) , and I’m trying to perform firmware updates over Wi-Fi using a firmware file hosted on an...
Hello, I need to configure and compile a sample to send an audio stream (mp3) to the I2S interface.
I tried to put together some configuration from other samples but no...
Hello,
I’m trying to run the TensorFlow Lite Micro example (zephyr_samples/hello_world) on my nRF5340DK using nRF Connect SDK 2.6.1, but I’m unable to build the project...
hi support team,
when i testing wifi location, i found out one problem:
nrf_cloud_rest: Failed to encode location request, err: -12
that is this code in nrf_cloud_rest...
We need to set a GPIO pin in MCUBoot to activate an external USB hub chip so the USB DFU will work. I would like to do this with code in our project rather than directly modifying...
According to the nRF52832 Product Specification, “A step increase in supply voltage of 300 mV or more, with rise time of 300 ms or less, within the valid supply range, may...
hi,
i want to add uart function to my application. so i added necessary .c files to my project. if i compile the program i am getting these errors.
when i change the...
Hi,
I have Raspberry PI 3 Model B Rev 1.2 running "Linux raspberrypi 4.9.41-v7+ #1023 SMP Tue Aug 8 16:00:15 BST 2017 armv7l GNU/Linux". Running BlueZ 5.43
I can connect...
Hi community,
Try use FDS to write some data before sleep.
Following example and test is work.
But I try write data before into
sd_power_system_off();
...
Firstly the develop environment.
Windows 10
KEIL as IDE
Device: nrf 51822 - sd s130 2.0.1 - SDK 12.1 nRF5_SDK_12.0.0_12f24da.zip
Use case:
We have 2 application mode...
Hello i am using segger studio i have recently purchased three nrf52dk speically for ble mesh..
i am trying to run examples of mesh alpha sdk that nordiac prvodies but it...
We were playing with renaming some of our test devices to use emoji and other multi-byte utf-8 characters. We have a custom characteristic that allows renaming (since iOS...
dear nordic employee:
I tried to download the project of the ble_app_hrs_c_central by keil(nrf52832)
but It show like the title
I know I should reset the IROM1 and...
Is there a way to get the supervision timeout counter from the peripheral side? I am currently working with nRF5X modules and starting with the nordic uart example from the...
I'm using nRF52832, soft device 2.0, SDK11 and as a central.
When it happens I'm scanning for peripheral to connect. Usually it's a peripheral advertises at very low rate...
Hello,
I'd like to work with my nrf52832 DK while traveling(sins I do that alot recently) and would like to download somehow all of the pages in nordic's info centre to...
It's clear an Android device can be a central, but I'm having a hard time finding any information indicating an Android device cab be a peripheral that an NRF52 could be programmed...
Our products should connect to a central device. This central device should also be a peripheral which a phone can connect to. Will this be possible? If not, could the phone...
Hi, I need some guidance or an more in-depth example on adding the necessary code to read/write on the UART1 using the serial module or something else. Everything I've tried...
I am working with nRFx modules and have a few questions about updating parameters. I started my project with an example and modified what I needed. However, I am not sure...
