I attempted to create bluetooth central and peripheral apps using two nRF52840 boards that connect to each other and no one else using the device name. I had limited success...
Hello
I have just received thingy:91 x to start learning nrf platform. Unfortunately it's not all smooth. I am trying to do flash Blank application. It builds fine but then...
Hi, We have used nPM1300 on our development board around nRF54H20, but we are experiencing an strange issue. - when power is attached VBUSINILIM0/VBUSINILIMSTARTUP value is...
Hi,
We’ve successfully developed our first few custom development boards based on the nRF54H20 MCU, using the Fanstel BM20C module. However, we've discovered that the module...
Hello Nordic,
I am looking for a sample or instruction (step by step) for custom bootloader.
Our application code is ready and all the left thing is BLE DFU and custom...
Hey All
Im working on a new product and its the first time I'm developing around the nrf5340, I'm looking for some guidance around the supply configuration for maximum...
Hi Team,
We are using nRF9160 MQTT sample code 'mqtt_simple'.
1. What is the maximum payload we can send in one single PUBLISH?
2. I want to send 4KB of data in single...
Dear All,
I would like to order Li-Po batteries for my nRF52840 development kits and need some information. From the battery, what type of female battery connector is needed...
Hi, I can't get 250Kbps working on the nRF24LE1. I'm using the enhanced shockburst examples in the nRFgo SDK (enhanced_shockburst_ptx_nrf2 and enhanced_shockburst_prx_nrf2...
Hi,
By mistake, I clicked 'fill with zero' button in Jflash, may I ask, is my chip bricked because of this? Thanks.
The following lists my steps:
program the...
Hi,
I'm trying to use the SysTick timer on nRF52 to time some various tasks for debugging. I configured it like so, which I expected would cause SysTick_Handler to be called...
I didn't find any documentation in the peer manager for the need of this write buffers.
I do understand, that peer device data is stored there before written to flash. But...
Dear Nordic,
Device: nRF51422. Protocol: ANT+. Softdevice: S210 v5.0.0
I have 3 devices: two masters (No. 1 and 2) and one slave (No. 3). In my application, I pair the...
Hi guys
I have one nrf 51822 demo board.
And I want to buy one more board as BLE sniffer.
Can I use a nrf52832 demo board as sniffer to grab packet between phone...
Hi guys
I am programming nrf51822 demo board with sdk11 and try to finish service tutorials .
I finish all step in service tutorials and try to get service information...
Hi guys
I am using SPI example code in SDK11 (./nRF5_SDK_11.0.0_89a8197\examples\peripheral\spi) with nRF51 DK.
It works fine when send first data.
But it get in...
Hello ,I work with the sdk 12, I have a program to contoler the level of battery, it works, except that I recode 3870 mV (with USB) and when I measure the pin VDD I find 2...
Hello,
I am using an Android application to send data to a nRF52 board. The nRF52 board is the peripheral and the Android phone is the central. This is the link establishment...
Hi, I am trying test nRF52840-pdk throughput.
-I loaded softdevice s140_nrf52840_5.0.0-3.alpha_softdevice.hex into nRF52840-pdk using nRFgo
-Then I build (using uVision...
Hi, the datasheet for the nRF24L0+ says that the CRC is the mandatory error detection mechanism in the packet (page 28). Being that CRC can be enabled or disabled via EN_CRC...
Is there a problem logging into Nordic site ?
I have tried resetting my password and it doesn't seem to work. Had posted a question in the this thread earlier
