Hello,
I recently tried some examples with nRF53 + nRF7002 (e.g. ble_coex example).
However, I am developing with nRF54 and I would like to understand if the combo nRF54...
Dear Nordic Support Team,
We are in the process of integrating the Nordic nRF Mesh SDK (version 3.3.4) into our custom Java-based application and require your guidance on...
Hi
I am working with a custom board with nrf52832 with only 32Mhz external crystal. My application is working in the nrf52832 development kit but when I use the custom board...
NCS 2.9.1
NRF52840
Sysbuild but with only a single image (no bootloader)
I've been trying to figure out how to change the merged.hex output and how to perform additional...
Hi!
With SDK15, I figured that is possible to change the advertisement content on the fly by overwriting the content of `adv_data.adv_data.p_data` and updating `adv_data...
Hello,
I attempted to follow the nrfutil offline install instructions. However, I keep receiving the following error when trying to install the device package on the remote...
Regarding the radio peripheral, I stumbled upon these 2 properties and have no idea what they are for.
What's access address? And what is a channel? Shouldn't there be...
I am runing ble_connectivity example with simple_uart instead of app_uart was not working unable to scan not getting advertisement reports.
Its been working with PCA10001...
Hi,
I have a pretty simple problem but I can't get it right. This is what I want to do:
T=000, PIN_x = 0
T=004, PIN_x = 1
T=100, call a routine
T=543, Start over...
Hi,
In the BLE_UART example code posted here , I noticed a discrepancy with the SD 3.0 migration document, SDK12, and the example code.
In stock SDK 12.1.0, ble_stack_handler_types...
Hello everyone, i need some help and suggestions in understanding what is exactly happening. I have read a lot about bugs and workarounds in pstorage and now i actually don...
Hi, when reading radio transmitter peripheral example, I got stuck a bit on radio_configure(). I got stuck because I can only get some brief from the corresponding .h file...
i m using nrf51.... first i have call WFI(); and device goes to sleep mode...and when press any switch on gpio so, wack-up again...so, may i know that.. how many way for wack...
i m using gcc toochain setup in windows for pca10028 devlopment kit... and load BLE_UART code inside it... and now i m add onother rtc code inside it.. but it's not work....
main.c hello sir.. i m place rtc example code inside of ble_uart code .. and i m using gcc tool chain setup for pca10028 bord... code complile sucsessfully... code not work...
Hello all,
I want to use a single bank bootloader with the ISP1302 Module (nRF51822 Chip) and S110 (V8) Soft Device, SDK 10, for application update
Can I use the BLE...
when i use nrfjprog.exe download my application code,Change nrfjprog.exe --eraseall --program ble_module.hex --verify --reset to nrfjprog.exe --eraseall --program ble_module...
My apologies, but I just want someone to give me a quick brief on what are these things and how they work. AFAIK, the nrf51xxx series SoCs render limited, sporatic radio availability...
Hi,
I am Working on a BLE application in which I do not want to expose certain services until I am securely paired/bonded to a valid device. The problem is that during...
Hi,
I'm trying to use sd_ble_gattc_characteristics_discover to figure out which characteristics are in a service.
On the whole it seems pretty obvious (keep calling...
I'm using the nRF52 + SDK11.0.0 + s132 and the ble_hrs example. The function conn_params_init() is called to initialize the connection parameters that the peripheral will...
