Hello Nordic Engineers and community members,
I received an nRF7002-DK 1.0.2. (S/N: 1050757935), from Digi-Key today.
I've been following the YouTube video, "Getting Started...
i just rebuilt the code in the beacon_advertiser.zip file attach to this issue for the NRF52232....
the code runs as expected, though consumes about 200uA when sleeping...
I am using NCS v2.9.1 and trying to enable a bootloader chain with NSIB and MCUboot. The regular setup works fine, however if I try to enable the minimal configuration, I...
Our design has an nRF5340 with RV3028C7 to provide the 32 kHz clock via P0.00.
If I configure P0.00 as a digital input, I can see the pin toggling.
However, if I use the...
I had been doing this:
What it does:
create a CHG (channel group)
DPPI is triggered by a GPIOTE in-event
DPPI then triggers and EGU, a TIMER capture, and...
DPPI...
Hello
According to Enhanced ShockBurst (ESB) documentation , to stop the ESB module you need to call esb_disable(), but it also says that you need to check if the module...
Hi Team,
We are using nRF9160 modem and SDK 1.7 version with Segger Embedded Studio.
Using at_client sample code, observations as below.
1. Tried to read APN configuration...
Hi All,
I'm trying to update the application firmware of an nRF52 board with OTA DFU.
I have managed to create a .zip package (under linx, gcc compiler, Nordic SDK11,...
I want to make a program for wireless accelerometer with a microcontroller "nrf51822". I prepared the code however I face a problem with the ".h" files such as "nrf_error...
Hi All,
I'm having trouble running one of my I2C sensors connected to the nrf52 when running at a 200hz sampling rate.
Interestingly enough, the same sensor seems to...
I mean what kind of header information and stuff besides the data. I could only find this for advertising packets.
A graphic or list like this would be nice:
byte 0...
Hello,
I'm currently working on profiling an embedded application on an nRF52 using the S132 SoftDevice.
I've found that the svcall sd_softdevice_enable takes approximately...
Hi,
My SDK version:9.0
SD:8.0
I use gpiote to generate an interrupt,
static void bma255_int_hook(nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
g_int1_triggered...
My phone : Lenovo Phab
Problem : cannot pair with nRf 51822 from Bluetooth menu BUT when i use Official App ( NRF Utility etc) then connect and start receiving data " ...
Hi,
I am using nrf52 with sdk11.0, I have migrated the code of pwm_library code to ble_uart_peripheral.
But when i'm initializing the pwm the code it stops the advertising...
I am not sure where to post this info so I do it here. We have been testing nRF51822 chips in a Rigado BMD-200 module powered by a single 2032 battery and have been getting...
I am using the minimal port referenced in this question: devzone.nordicsemi.com/.../
to interface the nRF8001 using an MSP430 device. I am currently in the process of porting...
I am using SPI MASTER example from sdk 7.2.0 with softdevice s110(using spi along with BLE).
In my program I have a requirement of reconfiguring spi pins after using spi...
I see that driver version 1.0.0 was tagged on ghitub: github.com/.../v1.0.0
However, when I visit this page: www.nordicsemi.com/.../38649 , I can only find the 0.5.0 version...
Hi
I use nRF51422 for our products.
In a product line, we check the CWtest mode current consumption current.
I decided the determination value of the CWtest mode current...
Hi.
I'm using nRF51822, S130, SDK10.0.0.
I made a source code as below refering radio_test which is in SDK examples.
But the width of frequency is just 0.2MHz as below...
