Smartbadge epaper custom board using nrf5340/nrf7002, with an NFC loop to allow NFC card emulation/communication. Building using NCS2.9 with sysbuild.
I want to be able...
Hi,
Per Case ID: 298180, Nordic will help tune an antenna.
I have completed my first design and attempted to duplicate the meander antenna from the nRF52840 dongle...
Hi,I have been using I2S communication in nrf54l15 DK board with zephyr but couldn't able to get clock to I2s .I couldn't able to get configure clock in overlay file ,can...
I am running a modified asset_tracker_v2 on a nRF9160. all is working fine. I am upgrading from SDK v2.5 to SDK 2.90. After a build I find the merged.hex file under the build...
Hi!
I'm trying to decipher the MPSL FEM API documentation and I'm adding code to a bare metal project to initialize the simple gpio interface FEM config.
I'm running ...
I'm looking at Product Specification v1.2 - Reference Circuitry Configuration 2 where BUCK2 is not used. The schematic shows the output VOUT2 is tied to VSYS in this case...
I have a BLE system where multiple sensors operate as peripherals and send data to a BLE central. These sensors enter sleep mode after transmitting data and later wake up...
Hi Man,
How many CENTRAL_LINK_COUNT in ble_app_hrs_rscs_relay can do so far?
I just increase the CENTRAL_LINK_COUNT form 2 to 5 then nRF52 Reset itself all the time.
...
Hi,
I'm trying to run my application on your PCA10031 and PCA10000 USB Dongles and I'm having a problem getting the UART receive to work on the PCA10000-- my application...
Hi,
I want to to use an external ADC for the NRF51 since the resolution for the NRF51 goes up to 10 bits and I want to use a system that goes up to 16 bits that has a sampling...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Are there documents other than "S110 nRF51822 SoftDevice Specification v1.2" that describe the SoftDevice resource usage? I am particularly interested in the S130 on the nRF52822...
Hi,
I`m a newbie user of nrf52, i want to know what are the neccesary libs to configure the BLE on nrf52 and what are the steps from the scratch.
Thanks
Hi,
I am using nRF52832 with S132_V2.0.1 and SDK_11.0.0. I have set advertisement interval at 2 second.
I have observe one thing in advertisement that many times device...
Hi!I work with a Beacon Kit (nrf51822) and I would like to know which is its default radio transmit power and the velocity of transmission. In my application I sent via Ble...
Hi,
I'm using the reference project "Experimental: Eddystone Beacon Application" to transmit Eddystone URL packets and I'm sniffing the data with Wireshark.
I noticed...
Hi,
I'm using nrf51822 board with SDK 10 and S110 softdevice.
My application is based on uart over ble. It take 20 bytes data from a android device using nus, store that...
I have created files before with s110 sd8 with the
nrfutil.exe utility using a bat file.
nrfutil.exe dfu genpkg --application nrf51422_xxac_s110.hex --application-version...
Hello,
I want to connect one board trough SPI to my nRF51-DK. Using SDK11 and SD130, the nRF51-DK is the SPI master, I call the function nrf_drv_spi_transfer() but the...
Hi ,
In my project , i can use the battery service in my project.
But if i want to use the another four ADC channels , how to add it ?
my project is working at SDK 9...
Hi,
I am using 2 nRF52832, one for ESB Tx and one for ESB Rx used to send payload through UART using SDK11.
Tx board is used has a low power transmitter which transmit...
