I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
I have a custom board with a nRF5340 and need to configure VREGH in DC-DC mode and set 3.0V output on it.
I see the documentation on REGULATORS — Regulator control where...
Hi,
NRF54L15, nordic sdk version 2.9.1
I recently lost ability to build my application. I get this linker error:
/home/adam/ncs/toolchains/b77d8c1312/opt/zephyr-sdk...
Hello, I use the example ble_app_hrs_c_s130_pca10031 with the nrf51 dongle (#define ENABLE_DEBUG_LOG_SUPPORT) and a nrf51822 as a ble sniffer. In addition i use 2 Polar H7...
Hi,
I need a .bin file of the whole flash memory for production programming.
The procedure I have used until now (with s310v2) was the following:
Upload .hex file...
Hi.
I'm using the nRF51 DK (PCA10028) to mesure the curent consuption of my system.
I'm using an external DCDC witch is a part of my system, so I want to mesure the current...
Hi,
I was trying to send notification from nRF51822 to an android central when notification is enabled on the nordic uart rx characteristic and I discovered that if I enable...
I am building a WSN has several peripherals (custom nRF51822) and one central device (PCA10031 in serialisation connected to a PC and using the nrf51-ble-driver_win_0.4.0...
It seems to be a straightforward BLE app but I cannot make it work.
I start fresh from the “ble_app_template” in nRF51 SDK 8.0.0, and try to add two service data (battery...
I want to give my own custom characteristics fully unique UUIDs, but am unsure how to generate those.
Is there a procedure to generate a custom, vendor-specific base UUID...
Hello,
I'm developing on a nrf51822 with the S110 softdevice.
To save power, I use the sd_app_evt_wait() function to go into sleep mode.
To wake up, i want to use an...
Hi all,
I developed a program that works fine on the dongle. The dongle has a chip with product code: N51822 QFAAG0 1342AA. When I upload the program including the correct...
I'm using s110 softdevice 6.1 SDK. I do bonding in my application the same way as in the ble_app_hrs example (bond, no_mitm). I have a charactarestic set to SEC_MODE_SET_ENC_NO_MITM...
my chip is nrf51822,I used s110-sd-v7, it's work. I switched the software to s110-sd-v8, GPIO interrupt is high priority (APP_IRQ_PRIORITY_HIGH). I erase the flash (pstorage_raw_clear...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
