We are running an HCI controller on nRF52833 based on the Zephyr hci_uart sample code. We are using the Zephyr 3.7.0 LTS version.
We have set CONFIG_BT_CTLR_DATA_LENGTH_MAX...
Hi,
Platform: nRF54L15, SDK 2.9
The application is Matter + BLE. CONFIG_CHIP_DFU_OVER_BT_SMP & MCUBoot are part of the configuration. As soon as we enable the BLE...
Hello,
I'm reading about 700 values from an LSM6SDO gyro/accelerometers per second and need to store them, before sending them over bluetooth once where I store them is...
Hi, I was trying to flash the sweyntooth firmware to nRF52840 dongle using nRF connect for desktop. I was following the instruction on in this tutorial: . The hex file I used...
I have found that in NCS SDK 2.6.2 it was very simple to enable FLASH_SIMULATOR as part of the mcuboot configuration overlays. But starting from SDK 2.7.0, I keep getting...
We are looking to do DFU over UART to the Application as described in DevAcademy nRF Connect SDK Intermediate, Lesson 8, Exercise 1, Step 5. However, we have only one UART...
I am working to convert from Thingy 91 to Thingy 91x. I have successfully used the modem_shell with RTT output and control and the overlay does not seem to work with SDK 2...
Hi,
I'm looking to work with a Bluetooth LE master device. From what I read the nRF51822 should be able to function as a Master device (the dongle is configured to be a...
Hi all
I want to load the (UART_example) flash image compile with Keil by nRFgo studio,
but a program fail occur as below screenshot:
any idea?
Thanks.
I have test RTC example on both different hardware revision nRF51822 chip.
1)N51822 QFAAC0 1309AF
2)N51822 QFAAC0 1308AE
1309AF revision chip is function properly with...
I'm confused about how to assign a functional block's I/O (TWI in my case) to a particular pin on the device. Is there a worked and documented example? Is there a relevant...
I am trying to get wireless communication implemented on a robotics project I am working on. I'm using a PIC18F4550, PIC18F2550, and two Nordic nRF24L01's. I'm having trouble...
I'm attempting to have two separate evaluation boards talk to each other through the GHz Radio. I've read the docs, and they explain that I have to set the radio in either...
Hi, I am using a app_gpiote_user_register to register a gpiote user and then enabling it, before I set the pins this user detect to be input using nrf_gpio_cfg_input. When...
Using eclipse and code sorcery compiler I got an undefined label error, see below
[b]_build/gcc_startup_nrf51.o: In function Reset_Handler': /home/oscar/workspace/Nordic...
Hi everyone:
use Gazell to builder multi-node .
so i have to re-enable pipe number on connect state.
my Fragment code about "open/close pipe".
but it not work correctly...
In nrf_gpiote.h:
The workaround code for PAN_028 OUTINIT anomaly (#9) will cause the GPIO to glitch to the undesired state if it is already assigned to a GPIOTE and in...
I'm trying to use the NOACK mode for some packets on the transmitter side,
and W_ACK_PAYLOAD on the receiver side.
My problem is that if the receiver gets a packet with...
Hi,
mi question is about how to configure in a good and complete way Timer1 and Timer2, so trying to be more specific with my Question:
I need timers with a Tick of 250ns...
We are creating the source program for examining RF module which uses nRF24LU1P.
It is the program that it transmits on the frequency specified from PC.
The API of USB...
I'm attempting to write my own Service based on an example; there are two simple Characteristics in the design. During the discovery process, however, I'm getting the following...
