Hello, I am currently developing UART communication firmware for the nRF52805, but I am encountering issues with performing DFU firmware updates.
Below are the details of...
Enabling coded broadcast compilation may result in undefined coded parameters, and coded scanning may also generate errors. May I know which SDK version will support these...
I wrote a simple terminal that reads the keyboard input from USB UART device and echos it back to the same device. It works as follows: 1. It registers an interrupt handler...
Hello,
I using ncs v3.1.1 SLM on nrf9151 to send messages to a CoAP server. It seems nrf9151 by default uses AES_128_CBC_SHA256 even though on the server side, we have given...
Hi, I am unable to read GPIOs (always getting 0x00000000 from gpio_port_get or 0 from gpio_pin_get). My main project is https://github.com/marcuswu/leaf-fall/tree/main/firmware...
The DECT Nr+ shell (the MAC version, not the -phy; tested with v3.3.0-ba167d9f3db4) offers IPv6 connectivity.
The DECT standard has a profile for IPv6 described in ETSI...
Hello,
Overview:
Currently we are using nRF9160 we are using mbedtls library for generating EC key based certificates (self-signed and CSR). Our code is built with TFM...
Hi,
On what occations do the BLE_GAP_TIMEOUT_SRC_ADVERTISING and BLE_GAP_TIMEOUT_SRC_SCAN events fire? The documentation is a tad ... terse .
regards,
Elm
Hy world,
I can update my device with FOTA, but the first time i do:
1 I put: "ble_default_bootloader.hex" on board;
2 i open nrfMasterControlPanel app
3 i write characteristic...
I have a feeling I am missing something completely obvious here. That said, this problem has cost me enough time today that I'm willing to risk embarrassment to see if someone...
I'm trying to implement a simultaneous broadcaster observer by calling ble_gap_adv_start() and sd_ble_gap_scan_start() and waiting for respective events.
If I call advertising...
Hello,
I'm trying to use Eclipse with a Nordic SDK (managed build mode) but it seems Eclipse (latest Mars edition) fails to invoke the assembler. Here is what I found in...
We are looking to use the DCDC to reduce the maximum current during radio operations, but minimize the overall current by enabling it as late as possible before radio use...
I have added button in my project and used bsp_init() to initialize it. All functions in bsp_init() returns NRF_SUCCESS but if I push my button even gpiote_event_handler(...
Hi Folks,
i have implementet a sleep mode by using only the RTC timer with the 32KHz OSC and the WFI instruction. The current consumtion is around 1.7µA (all peripherals...
Hello,
We have some problems with nRFgo Studio on the one of our computers.
Firstly, it takes a long time to flash firmware - about 15-20 seconds:
Secondly, we...
I have interfaced a vibration switch with nRF51822 Pin 19 using external pull-up. When there is no vibration the switch is either at open position or close position randomly...
UPDATED WITH IMPLEMENTATION
Is there a way to know what is triggering a chip boot :
Power off (battery replacement or deffective electrical connection)
The watch...
I have an old project I am trying to recompile for nrf51822 but have been programming with the most recent MDK on my station. The project is asking for old Device Family pack...
Hi all!
I just tried to compile the DFU example from the nRF51_SDK_7.1.0_372d17a and I keep getting the building error:
Referred Memory Range 'IRAM2' is undefined
...
Hello,
Does nRF51822 has a MAC adress when we buy it ?
If yes, is it possible to have two nrF51 with the same MAC adress ?
If yes, can we buy a MAC adress range and...
