I'm trying to get NFC power-up/restart working on nrf54lDK but the call to sys_poweroff() results in: E: ***** BUS FAULT ***** E: Precise data bus error E: BFAR Address: 0x0...
Hi,
We have deployed some devices now, and we see quite some modem faults popping up.
Could you try to give all info on what you know about these faults we have from...
Environment
SoC: nRF54LM20 (DK; silicon reports nRF54LM20B ENGB — also reproduces built for the LM20A target)
nRF Connect SDK: v3.3.0-rc2, west v1.5.0
Bluetooth: SoftDevice...
Hello
We are using nRF5340 as our EVK with a 12 antenna array plate(4x4 with center 4 ones not being there). Our beacon uses nRF52833.
We used Nordic's sample codes- ...
Title: nRF52840 / OpenThread: how to inject custom IEEE 802.15.4 RX frames into the native receive path?
Hi,
I am working on a test setup around nRF52840, OpenThread,...
We are building a line of product to be used in big size building light management and control.
We believe that both the IV values and a huge quantity of SEQ separate counters...
Hello,
On a pairing failure from iOS (either cancel or timeout of the pairing dialog alert "Bluetooth Pairing Request"), the device no longer allows pairing until a software...
Recently our firmware team encountered a new version of NRF52840 and our hardware team "orders the available chip". How can I know and manage the version when we design the...
I was wondering whether having GATT client and server in same chip (NRF52832) would work? If so, then how would I need to set up bt_conn_auth_cb on zephyr if both uses passkey...
Hi,my board is nRF52840dK,and the SDK is ncs 2.7.0.
I want to modify the subevent parameters,
Is there any API to modify them in my code but not in prj.conf? such as ...
The provisioner sample was used as the base code for adding the function to set model's publication address. After doing so the end node goes into
Requesting Help regarding...
I currently am using a nRF9160DK. I want to have the nrf52840 on it scan for BLE devices and return the device count and then send this over UART to the nrf9160.
How can...
Hello,
I am contacting you today because I recently bought an nRF5340 development kit, as well as several Nordic Thingy devices (52, 53 and 91) and I have been working on...
Hello,
I am contacting you today because I recently bought an nRF5340 development kit, as well as several Nordic Thingy devices (52, 53 and 91) and I have been working on...
Hi, I was reading through the errata for SoftReset and see a note: [161] RESET: Network core is not fully reset after Force-OFF
Can you please clarify how to reset both...
I'm trying to use Adafruit LSM6DSOX (I think it's a misprint and it's actually LSM6DSO), regardless. I can get it to work using I2C but I need it over SPI.
I have been racking...
Hi,
I am working on a board combination of nrf52840 and HL7800 modem. So, I just migrated from 3.6.0 zephyr to 3.7.0 and ncs 2.7-branch.
modem driver: https://github.com...
Hello, I need to scan the advertising data of my peripheral wich advertise with extended advertsing and LE coded PHY.
I use zephyr 3.7, and I work if I use the BLE controller...
Using Modem FW 1.3.6. Using NCS 2.6.0.
We're experiencing an issue in a test setup where we are getting this error reported (528) when trying to clear/set root certificates...
Hello nRF Team,
I am developing a ble terminal app based on the Bluetooth: Peripheral UART sample (nRF Connect SDKv2.7.0) on nRF52840DK. I was testing the app BLE pairing...
When following the unit test example, and even with an alternate minimal implementation, I get the following error:
PS {nRF Connect terminal} > west build -b nrf52840dk...
