Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
Good day
I have noticed that when using a callback functions certain limitations exist. For example, adding functions to the callback function will run into an error or...
I am working on a BLE mesh project, and I have created my own BLE mesh publish and send functions,
My concern is, I am creating buffers using the bt_mesh_model_msg_init...
Hi,
This is a continuation of the below tickets:
After updating the modem firmware to 1.3.3 and recompiling Asset Tracker v2 with SDK 2.1, I'm afraid the problem...
Hello!
I am trying to connect my Thingy91 to nrfCloud, but after successfully activating the SIM card, I receive error 40412: No device found for this id. The device has...
Hello Team,
I am trying to develop an app with BLE example as the base and modifying it.
Hardware setup:
PC - Windows 10, nRF Connect launcher v3.6.1, BLE example...
Hello all,
Currently, I am trying to set up debugging functionality for a custom board using the JLink Plus. When I use the JLink RTT Viewer, I get the following:
Other...
hi team,
i have trying to wrote a code for analog to digital converter module in segger 5.40 using nrf52840 controller and and i found one example code related to analog...
Hello,
I've a "follow up" issue related to this ticket:
In an earlier state of our project, we've adopted the smp_svr application as our "DFU".
But during maturation...
Hi there,
We are running a power consumption test using PSM mode, and we are however not measuring the 4uA floor current as expected.
We are requesting a active time of...
Hi Sir,
I want to test advertising extensions feature with zephyr hci_usb on nrf52480.
Have any user guide to reference ? ex. linux hcitool or btmgmt commands.
Thanks...
Hello
I'm currently writing a program for an NRF52840 chip which reads some values from an ADC each second and writes them to an external flash chip. I'm trying to run this...
Hi Nordic support team,
nrf sdk for mesh 5.0.0, nrf sdk 17.0.2, nrf52832,
When I config the tx power for the mesh msg transmission I faced a problem. I found that there...
Hi, I would like to expand NRF_BLE_SCAN_DEF in the ble_app_blinky_c demo for better understanding -
Source: main.c:90
NRF_BLE_SCAN_DEF( m_scan); /**< Scanning module...
Greetings!
I have modified the "ble_app_uart_c" example from SDK v17.1.0 to be used to scan for and control our BLE-enabled devices via a terminal emulator. When we use...
Hello guys,
I'm currently trying to get notifications from a custom ble service. I can connect to the service, but I only see 6 out of 9 characteristics. The first pic shows...
