I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
I am transitioning a project from normal BLE to BLE mesh.
Flash space might be an issue.
Here is the flash layout I have so far. Purple is for nordic items and yellow...
I'm using SDK 15 on an nRF52840, compiling with Segger Embedded Studio.
I've created a project in SES using the project_template folder.
When I try to use both ESB and...
Hello,
I want to access the AIN input 6 ADC/LPCOMP input 6 to measure a current at two points with a defined time interval in between.
Since I am not familiar how to...
Hi,
I am trying to use UART in a blocking mode for nrf52840. I am able to transmit the bytes, but not receiving the bytes. While debugging, figured out that RXDRDY event...
Hi,
i have some issue regarding DFU-ing the bootloader.
Here is my command to generate zip file: nrfutil pkg generate --hw-version 52 --bootloader-version 1 --bootloader...
Dear Nordic Team:
I used nrf52832 as my BLE IC, and an IC of Novatek as my MCU. They are connected by uart. Now I need to merge ble_dfu and serial_dfu on the version of...
Errors while starting debugging session
I am getting error 65 'access violation' in Keil Uv5 and 4.
In IAR , I am getting 'User Error:Stack Pointer is setup into incorrect...
Hi,
I modiy the usbd_hid_generic example to tow endpoint by sdk15.0.When i use the USB testtool send some datas to usb deivce,the d atas cannot be read properly by NRF_USBD_EP_OK...
Hi, in our one project we are using nrf52832 radio to transmit the data packets. After transmitting the data packets, the nRF52832 chip need to disable the radio to minimize...
Using SDK 15.0.0, I have ported the peripheral/usbd example to custom hardware based on the nRF52840-QIAAC0.
In the nrf_drv_usbd_enable() function, execution hangs at
...
I'm communicating with a temperature sensor using I2C/TWI and I'm now trying to send that received data over BLE using the HTS service.
When I send a ble_hts_meas_t with...
Hello,
I am using nRF52 with ADS1292, and i am trying to sample at 8kHz with data throughput of 72kB/s, but some data is being randomly shifted giving me random spikes...
Hi Nordic Team,
I am requesting any block diagram level documentations - on a high level software architecture overview of SDK.
My goal is to understand how different...
Hello All,
I want to know Maximum External flash size supported by nrf52832 .
On which parameter Maximum size of external flash depends?
If it depends on usage, then...
Hello,
I'm currently using a bootloader based on the one included with SDK 15. We're close to mass production and I need to decide on how much space I should leave for the...
