I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
About DM_LOG, DM_ERR, I define ENABLE_DEBUG_LOG_SUPPORT in Options for Target->C/C++->Define, the "string" will be sent over UART.
But ADV_LOG still does not work，How should...
Hi Nordic,
I am using ESB_DPL SDK ver 13 for communication between one nRF51822 transmitter and multiple nRF51822 receivers with data whitening. I do not want the receiver...
I ported both the provisioner and provisionee program respectively to 2 different boards, but couldn't detect the advertising package of neither.
Do they send exclusively...
Hi all
I've two questions regarding errata 156:
Am I assuming right that, as long as I don't use WFI or WFE, this errata has not effect?
Are the two consecutive...
Hi. I'm using nRF52832.
I want to add LEDs. Can it drive 20mA for LED?
As I see the datasheet, GPIO pins have "High drive" function. What deos it mean?
I hope your reply...
Hello,
I am having difficulty downloading an application using the sample images provided. It looks like the application boots into the bootloader, there is a brief message...
Hi,
I modified the blinky_freertos example from SDK 12 slightly to perform the following:
I have one timer and one task. The task blinks a LED and then suspends. In...
I'm trying use an nRF51 PDK to upload firmware (or, rather, just confirm that I can upload firmware) to one of these modules:
www.wireless-tag.com/.../WT51822-S4AT.html...
Hi,
I am new in BLE and working on existing product. i am adding BLE functionality in the existing product hence having one host MCU on my board. My product will be in...
Hi There,
I am doing current measurements on the nrf52840 in sleep mode with no RAM retention and I am getting different values based on how I take the measurements. Please...
I am attempting to interface a Winbond flash device with the NRF52. The
datasheet does not specify the idle state of MOSI when reading from the device. However, I cannot...
We started with the default project that have no heap.
Added mallocs to the system and they seemed to succeed, without realizing heap was set to 0. They did not return NULL...
hello
we have custom board with Nrf52840.
i already test the uart code on nrf52840 dk..every thing is working great.
my custom board is connect to the nrf52840 dk with...
Hi
I have a PCA10040 V1.1.0 that my company has been using to flash test code onto other nRF52832 chips (I don't know the details, but it has wires attached to the debug...
