Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi
I'm using the Eval Kit PCA 10001 V2.1.0 and Nexus 5 with new Android version 4.4.2. Connecting to the Eval Kit works just fine, but when i perform a service discovery...
I have an nRF51822-based peripheral using the SoftDevice 110 v7.0.0 and SDK v6.0.0. The peripheral uses two custom characteristics under a single custom service. I'm using...
Hi
I'm using sd_app_evt_wait(); to go into low_power mode.
For some reason it comes back immediately, but I can't figure out why.
If I call it a second time it stays...
Hi,
I'm trying to flash the S110 onto my nrf51822 SoC, but nRFgo gives me the following error. (Also, hitting recover just gives me an error: "an error condition was detected...
Within app_button module, code for app_button_is_pushed() seems to have changed from SDK version 5.1 to 6.0. I notice my code has stopped working properly with that update...
Hi
Now, we are planning to implement an ANT+ RX (slave). I checked nRF51422 product spec. Radio current consumption is 12~13mA if receiving data between 250kbps and 2Mbps...
I'm using the boot loader that comes with the beacon development kit and I want to change it so that when the application software is running it can restart the device in...
I have managed to get the SPIS block working using standard sets of read and transmit buffers. This all works.
I am now trying to use the ORC register to send a single...
I am wondering how you put the nrf51822 chip to sleep. I've determined that the way to do this with the soft device is sd_app_event_wait() in the while loop. What about non...
Hello
I've been trying to create a simple BLE observer that outputs the nearby devices data onto the serial port using a PCA10001 board.
For this, I'm adapting the code...
Hi - I'm using the 51422 dfu bootloader from the nrf 6.0.0 SDK and it works fine with the iOS apps, I can send both .bin and .hex files to the device and it works fine. However...
Hi,
I am using nRF51822 evaluation kit. I want to develop GPIO isr (GPIOTE_IRQHandler) which can handle multiple GPIO interrupts. I have tried to enable the GPIOTE_IRQHandler...
Hi!
When using bootloader, I cannot update application data from Keil (for example for debuging), because after restarting bootloader is loaded and
!bootloader_app_is_valid...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...