Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I'm having an issue getting the SLM example to compile with UART2.
Steps to reproduce:
Configure project with UART2
See error pop-up
Compile anyways
See Undefined...
Hello, I am a beginner to start developing with your nRF52810 chip.
In the near future, I would like to implement Bluetooth long range communication with this chip.
...
Hello,
We are planning on running the nRF9160 with two supplies. VDD_GPIO=1.8V and VDD=3.8V to get the best cell performance.
Can you tell me if I can turn off VDD_GPIO...
Hi,
I develop a device with a GPRS modem. GPRS modem is controlled by nrf52840 and it is impossible to use two devices for DFU process.
SDK: 17.0.2
SoftDevice: s140...
I want to send adc data to Bluetooth.
I downloaded the source code below and compiled it. https://github.com/NordicPlayground/nRF52-ADC-examples/tree/master/ble_app_uart__saadc_timer_driven__scan_mode...
Is there sample code to use a FAT Filesystem on the Macronix memory on the nRF9160-DK? The full_modem_update sample uses the Flash but not as a filesystem.
It would be great...
I have a modified asset_tracker that has been running on all of the previous versions of asset_tracker. I have I2C settings in prj.conf as shown below that I copied from each...
I am just starting out with the nRF5340 and I see that it has an NFC antenna. Can it read an external NFC tag without additional circuitry or does it require an external reader...
Using SDK 15.2, PCA10056 Dev Kit. Segger Embedded Studio. s140_nrf52_6.1.0_softdevice.hex
Our Code (non Long Range) works perfectly! We are using it in a test for a customer...
I am using sd140 on a ble central and peripheral that uses the ble uart example code.
The peripheral always returns NRF_ERROR_BUSY when calling ble_nus_data_send(). This...
Is it possible to run ble_central and ble_peripheral as two threads using freeRTOS on the nrf52832 chip? Is freeRTOS on nrf52 is on an experimental stage?
Recently, I've found that the peer manager sometimes wrote specific information so many times
until the FDS storage went full.
An example data in the storage is as follows...
Hi, I'm trying to flash .hex file using J-FLash lite to nRF52840DK board using P18 Debug In (by SWD Interface).
I'm aware of pin out of J-Link Plus for SWD from https:/...
Hi
I tried to test the read and write in flash but without success. I added the following code in service_init()
uint8_t initial_data[8];
err_code = nrf_fstorage_read...
We have a design that uses a simple custom board with an NRF52832 chip, button, accelerometer and onboard battery. For many phones, the operation is quite stable - we connect...
