Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
While getting myself familiar with new SDK12 features I've noticed that when nrf_log uses deferred logging to RTT NRF_LOG_FINAL_FLUSH() results in unconditional breakpoint...
Hi guys,
Wanted to play around with the new SDK and the S332 Softdevice. I tried your multiprotocol example "ble_ant_app_hrm" with Keil.
Build fails:
http://dumptext...
Hi,
I am developing an app using the base module "ble_app_uart". In our application we would like to store data in the flash memory.
I am using "Flash Data Storage"...
I want to make my nRF52 turn on every 5 minutes, send data to a device over BLE and go back to sleep. For some reason once I turn on BLE advertising LED1 becomes solid and...
Dear Nordic Team,
Thanks for supporting.
We are worked in nRF51422 development kit.How can i enable DFU service in all BLE APP examples source codes in main.c
Please...
Hi,
when I use nRF Connect (or MCP before) to browse my BLE service, I get shown some garbage if I use many characteristics in my service.
When I use 45 characteristics...
Hello people,
I'd like to use the NRF52832 (QFAAB0) / PCA 10040 / S132 development board as a data logger. For that I soldered a micro-sd card reader and started using...
I set the connection as follows:
#define MIN_CONNECTION_INTERVAL (uint16_t) MSEC_TO_UNITS(500, UNIT_1_25_MS)
#define MAX_CONNECTION_INTERVAL (uint16_t) MSEC_TO_UNITS(1000...
I am trying to use the mesh network using the nrf51822. I have to use the app_timer with my application. Mesh library and the app_timer library making conflict with the SWI0...
I was trying out the low power PWM example and noticed the timing inaccuracy that was mentioned in documentation .
For example, with low_power_pwm_0,
period = 220...
I have checked the datasheet between 51422 and 51822,they look the same,but why the NRF51422 can flash BLE and ANT+,but 51822 can't? Is the Radio part different,or the Flash...
I have based my firmware on the Proximity Application example.
Now I need to extend my application to support BLE DFU service.
But as i read Extending your application...
Hi,
I am using the flash memory for a few variables and it works very well. Now I have one flag which is defined by #define statement and if it is enable then the initial...
hi,
i have nrf8122 module . want to flash a hex file in it by using nrf51 development kit. is it possible to flash code in the nrf51822 module. other wise please provide...
