I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,when i get connected to the phone,when i call err_code = ble_hts_measurement_send(&m_hts, &simulated_meas) and err_code = ble_bas_battery_level_update(&m_bas, battery_level...
I got the Dynastream N5 kit and have successfully used it with limited ANT work and was trying to get BLE working but can't get a driver for the USB dongle. On the 51422 product...
Hi All,
I am working in the sleep mode with system off and wake up with internal RC clock.
It function well when connected to EV board...
I see the "Emulated System...
How do I keep advertising when I have a connection come in? I'm a BLE peripheral.
I'm running SD 7, is there a particular flag or sequence I need to do now that I've upgraded...
Hey!
I'm testing out the new SoftDevice and am trying to update firmware OTA but thus far have not been able to do so. I've tried from the Master Control Panel android...
I'm using NRF51822 as SPI slave and STM32 as SPI master. Everything works fine except the first SPI transaction after resetting both boards.
On the first transaction I...
Hi guys,
I'm curious whether or not i can try the mbed platform on the EK board. The circuit of the mbed kit and the EK look pretty similar. All the LEDs and buttons are...
I'm using the NRF51822 - I've just started a project. I can build and load it into my target board. I enter debug mode, and I'm able to do step through the code, add breakpoints...
What are the iROM and iRAM settings for the v0.5 S130 softdevice for the nRF51822?
The S130 softdevice spec sheet provides some clues, but no specific settings.
I've...
To do development what software did you have to install, and what hardware did you need to get the MBH7BLZ02-EB-KIT working? What hardware did you connect together?
There...
Hi
I'm learning to use the sd_flash_write function to write words into flash memory. I've the SD enabled, but not advertising, so I'm able to debug. Scheduler is also initialized...
Hello, I am trying to make a portable temperature sensor using nRF51822. I made a sensor that basically amplifies voltage level when the temperature increases, and I want...
Recently, I try to programme nRF24L01P DK communicating with nRF2401e1 DK in shockBurst mode, transmitting and receiving,unfortunately，which does not success normally.
first...
Hi
Let's see if you can help me :-)
I've spent several days trying to compile the blinking example for NRF51822 in a more modern Eclipse environment. In fact, latest...
I'm now studying about Gazell.I'd like to get Gazell specification which describe about its packet format,network topology,and so on.
Moreover,does the nRF51822's Nordic...
Hi all,
i am having issues with the mKit and current consumption.
Just an FYI to measure consumption i am placing the mKIT in series with a shunt resistor and measuring...
I've spend some time figuring out where the application code should start for the S130 . Table 11 in the SoftDevice Specification v0.5 document indicates that it is at 0x00020000...
