I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
Hi,
I am developing an application which needs a precise reference clock of 20ms. I have a 32MHz Xtal on the PCB with a tolerance of +-10ppm. To configure the device to...
Hi
I'm using nrf toolchain/sdk 2.5.2.
Got a strange problem with my QSPI NOR flash interface. when i run flash_erase i get error message "qspi_nor: Failed to schedule...
I am running a nrf5340 with zigbee as a coordinator, I observed after a while that battery life of my end devices don't last as expected. Then after debugging I found that...
Hi Team,
We are developing a custom board using nRF52840 SoC. We need the storage and handling of IC, reflow solder profile of IC and assembly instructions if any.
Regards...
HI currently i am utilizing sdk ver 17.1.10 nrf52840 s140 we are using dfu/secure_bootloader/pca10056_ble app and i need to add UART app to it so that so we need both bootloader...
hardware:nrf5340+npm1300
software:ncs 2.5.1
hi professor,
If I just connect VBUS, The npm1300 will reset when I read bulk register. If I connect vbat and vbus, read...
In NRFX Oscillator header , accessing the function requires the preprocessor macro which in turn requires preprocessor conditional
The problem is that final conditional...
Hi, I am developing firmware for a project using a custom board with the nrf52832. The project requires mcuboot and secure BT OTA. When I enable the configs
CONFIG_BOOTLOADER_MCUBOOT...
Hi,
I'm trying to send gyro and acceleration values continuously using MPU6050(IMU) sensor through BLE after BLE connection is made with other device.
I took ble_app_uart...
I have a few questions regarding the power consumption calculation of the network and application cores from the 5340:
With the assumption that all peripherals are turned...
I am attempting to build a project off of the XXX template repository. So far I have gotten the workspace set up and am now attempting to run "west build" but I get the below...
Dear Support Team,
I just started evaluating a nRF52833 DK board with the nRF Connect SDK 2.3.0. At this point I would like to start playing with the SPI but unfortunately...
Hello.
I am developing device using nRF52840 and i have question about input voltage.
Circuit is converting remaining voltage of battery using nRF52840 (Pin P0.02 AIN0...
I'm using nrfSDK17 with 52832.
When I build my code ,I will get error ad follow:
As L6407E explain,It seem that I only need to scale up IRAM size no less than 0x58....
Hi,
There is one board level hardware change in our new board design that requires different GPIO behavior.
Is there a way to program board revision number in ROM (not...
